SAF-XC167CI-32F20F BB-A Infineon Technologies, SAF-XC167CI-32F20F BB-A Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAF-XC167CI-32F20F BB-A
Manufacturer Part Number
SAF-XC167CI-32F20F BB-A
Description
IC MCU 16BIT 256KB TQFP-144-19
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC167CI-32F20F_BB-A.pdf
(90 pages)
Specifications of SAF-XC167CI-32F20F BB-A
Core Processor
C166SV2
Core Size
16-Bit
Speed
20MHz
Connectivity
CAN, EBI/EMI, I²C, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 16x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LFQFP
For Use With
B158-H8963-X-X-7600IN - KIT EASY XC167CIMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
FX167CI32F20FBBANT
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
3.6
The CAPCOM units support generation and control of timing sequences on up to
32 channels with a maximum resolution of 1 system clock cycle (8 cycles in staggered
mode). The CAPCOM units are typically used to handle high speed I/O tasks such as
pulse and waveform generation, pulse width modulation (PMW), Digital to Analog (D/A)
conversion, software timing, or time recording relative to external events.
Four 16-bit timers (T0/T1, T7/T8) with reload registers provide two independent time
bases for each capture/compare register array.
The input clock for the timers is programmable to several prescaled values of the internal
system clock, or may be derived from an overflow/underflow of timer T6 in module GPT2.
This provides a wide range of variation for the timer period and resolution and allows
precise adjustments to the application specific requirements. In addition, external count
inputs for CAPCOM timers T0 and T7 allow event scheduling for the capture/compare
registers relative to external events.
Both of the two capture/compare register arrays contain 16 dual purpose
capture/compare registers, each of which may be individually allocated to either
CAPCOM timer T0 or T1 (T7 or T8, respectively), and programmed for capture or
compare function.
All registers of each module have each one port pin associated with it which serves as
an input pin for triggering the capture function, or as an output pin to indicate the
occurrence of a compare event.
Table 6
Compare Modes
Mode 0
Mode 1
Mode 2
Mode 3
Double Register
Mode
Single Event Mode
Data Sheet
Capture/Compare Units (CAPCOM1/2)
Compare Modes (CAPCOM1/2)
Function
Interrupt-only compare mode;
several compare interrupts per timer period are possible
Pin toggles on each compare match;
several compare events per timer period are possible
Interrupt-only compare mode;
only one compare interrupt per timer period is generated
Pin set ‘1’ on match; pin reset ‘0’ on compare timer overflow;
only one compare event per timer period is generated
Two registers operate on one pin;
pin toggles on each compare match;
several compare events per timer period are possible
Generates single edges or pulses;
can be used with any compare mode
34
Functional Description
XC167CI-32F
Derivatives
V1.1, 2006-08