SAK-XC161CS-32F40F BB-A Infineon Technologies, SAK-XC161CS-32F40F BB-A Datasheet - Page 61

• Manufacturer Part Number: SAK-XC161CS-32F40F BB-A
• Description: IC MCU 16BIT 256KB TQFP-144-19
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAK-XC161CS-32F40F BB-A

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 99
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 12x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LFQFP
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: ASC, CAN, IIC, SSC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 99
• Number Of Timers: 9
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Packages: PG-TQFP-144
• Max Clock Frequency: 40.0 MHz
• Sram (incl. Cache): 12.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 12
• Program Memory: 256.0 KByte
• For Use With: MCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: KX161CS32F40FBBANT; KX161CS32F40FBBAXT; SAKXC161CS32F40FBBAT; SP000098775; SP000224544

3) The pad supply voltage pins (
4) The total supply current in Sleep and Power down mode is the sum of the temperature dependent leakage
5) This parameter is determined mainly by the transistor leakage currents. This current heavily depends on the
6) All inputs (including JTAG pins and pins configured as inputs) at 0 V to 0.1 V or at
7) This parameter is determined mainly by the current consumed by the oscillator switched to low gain mode (see
Data Sheet
driver current is not covered by parameter
outputs are driven, because the drivers’ input stages are switched and also the Flash module draws some
power from the
current and the frequency dependent current for RTC and main oscillator or auxiliary oscillator (if active).
junction temperature (see
if no current flows through the port output drivers. Otherwise, the resulting temperature difference must be
taken into account.
outputs (including pins configured as outputs) disconnected. This parameter is tested at 25 °C and is valid for
T
Figure
given values refer to a typical circuitry and may change in case of a not optimized external oscillator circuitry.
J
≥ 25 °C.
11). This current, however, is influenced by the external oscillator circuitry (crystal, capacitors). The
V
DDP
supply.
Figure
V
DDP
12). The junction temperature
) mainly provide the current consumed by the pin output drivers. This output
I
DDP
. A small amount of current is consumed even though no
59
T
J
is the same as the ambient temperature
Electrical Parameters
V
DDP
XC161CS-32F
- 0.1 V to
Derivatives
V1.2, 2006-08
V
DDP
, all
T
A