DSP56311VL150 Freescale Semiconductor, DSP56311VL150 Datasheet - Page 13

• Manufacturer Part Number: DSP56311VL150
• Description: IC DSP 24BIT FIXED POINT 196-BGA
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of DSP56311VL150

• Interface: Host Interface, SSI, SCI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 384kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.80V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 196-MAPBGA
• Package: 196MA-BGA
• Numeric And Arithmetic Format: Fixed-Point
• Maximum Speed: 150 MHz
• Ram Size: 384 KB
• Device Million Instructions Per Second: 150 MIPS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Freescale Semiconductor
HA0
HAS/HAS
PB8
HA1
HA8
PB9
HA2
HA9
PB10
HCS/HCS
HA10
PB13
HRW
HRD/HRD
PB11
Signal Name
Input or Output
Input or Output
Input or Output
Input or Output
Input or Output
Type
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
State During
Ignored Input
Ignored Input
Ignored Input
Ignored Input
Ignored Input
Table 1-11.
Reset
DSP56311 Technical Data, Rev. 8
1,2
Host Address Input 0—When the HI08 is programmed to interface with a
nonmultiplexed host bus and the HI function is selected, this signal is line 0 of
the host address input bus.
Host Address Strobe—When the HI08 is programmed to interface with a
multiplexed host bus and the HI function is selected, this signal is the host
address strobe (HAS) Schmitt-trigger input. The polarity of the address strobe is
programmable but is configured active-low (HAS) following reset.
Port B 8—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Address Input 1—When the HI08 is programmed to interface with a
nonmultiplexed host bus and the HI function is selected, this signal is line 1 of
the host address (HA1) input bus.
Host Address 8—When the HI08 is programmed to interface with a multiplexed
host bus and the HI function is selected, this signal is line 8 of the host address
(HA8) input bus.
Port B 9—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Address Input 2—When the HI08 is programmed to interface with a
nonmultiplexed host bus and the HI function is selected, this signal is line 2 of
the host address (HA2) input bus.
Host Address 9—When the HI08 is programmed to interface with a multiplexed
host bus and the HI function is selected, this signal is line 9 of the host address
(HA9) input bus.
Port B 10—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Chip Select—When the HI08 is programmed to interface with a
nonmultiplexed host bus and the HI function is selected, this signal is the host
chip select (HCS) input. The polarity of the chip select is programmable but is
configured active-low (HCS) after reset.
Host Address 10—When the HI08 is programmed to interface with a
multiplexed host bus and the HI function is selected, this signal is line 10 of the
host address (HA10) input bus.
Port B 13—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Read/Write—When the HI08 is programmed to interface with a single-
data-strobe host bus and the HI function is selected, this signal is the Host
Read/Write (HRW) input.
Host Read Data—When the HI08 is programmed to interface with a double-
data-strobe host bus and the HI function is selected, this signal is the HRD
strobe Schmitt-trigger input. The polarity of the data strobe is programmable but
is configured as active-low (HRD) after reset.
Port B 11—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Interface (Continued)
Signal Description
Host Interface (HI08)
1-9