ST16C654IQ64-F Exar Corporation, ST16C654IQ64-F Datasheet - Page 31

• Manufacturer Part Number: ST16C654IQ64-F
• Description: IC UART FIFO 64B QUAD 64LQFP
• Manufacturer: Exar Corporation
• Type: Quad UART with 16-byte FIFOsr

Specifications of ST16C654IQ64-F

• Number Of Channels: 4, QUART
• Package / Case: 64-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS232
• Voltage - Supply: 2.97 V ~ 5.5 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 1.5 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.97 V
• Supply Current: 3 mA to 6 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 45 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 2.97 V to 5.5 V
• No. Of Channels: 4
• Uart Features: Infrared (IrDA) Encoder/Decoder
• Supply Voltage Range: 2.97V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1273

xr
REV. 5.0.2
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be set to a logic zero during 68 mode.
•
•
MCR[4]: Internal Loopback Enable
•
•
MCR[5]: Xon-Any Enable
•
•
MCR[6]: Infrared Encoder/Decoder Enable
•
•
MCR[7]: Clock Prescaler Select
•
•
This register provides the status of data transfers between the UART and the host. If IER bit-2 is enabled, LSR
bit 1 will generate an interrupt immediately and LSR bits 2-4 will generate an interrupt when a character with an
error is in the RHR.
LSR[0]: Receive Data Ready Indicator
•
•
4.8
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During loopback mode, it sets
OP2# internally to a logic 1.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During loopback mode, it sets OP2# internally
to a logic 0.
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the 654 is programmed to use the Xon/Xoff flow control.
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. The RX FIFO may need to be flushed upon enable. While in this mode, the infrared TX output
will be a logic 0 during idle data conditions.
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
Line Status Register (LSR) - Read Only
INTSEL
P
0
0
1
IN
MCR
B
T
IT
X
0
1
ABLE
-3
14: INT O
INT A-D O
31
UTPUT
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
Three-State
UTPUTS IN
Active
Active
M
ODES
16 M
ODE
ST16C654/654D