XR16L788IQ-F Exar Corporation, XR16L788IQ-F Datasheet - Page 40

• Manufacturer Part Number: XR16L788IQ-F
• Description: IC UART 64B 3.3V OCTAL 100QFP
• Manufacturer: Exar Corporation
• Type: IrDA or RS- 485r

Specifications of XR16L788IQ-F

• Number Of Channels: 8
• Package / Case: 100-BQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 2.97 V ~ 5.5 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.97 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V or 5 V
• No. Of Channels: 8
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 2.97V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: QFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1284

XR16L788
HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See in
bit 6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR# output will
de-assert at 60 and re-assert at 16.
Enhanced features are enabled or disabled using this register. Bit 0-3 provide single or dual consecutive
character software flow control selection (see
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[3:0]: Software Flow Control Select
Combinations of software flow control can be selected by programming these bits.
4.13
EFR
C
ONT
X
X
X
0
0
1
0
1
1
0
1
0
Enhanced Feature Register (EFR) - Read/Write
BIT
-3
-3
EFR
C
ONT
X
X
X
0
0
0
1
1
0
1
1
0
BIT
-2
-2
T
ABLE
EFR
C
ONT
18: S
X
X
X
X
0
0
1
0
1
1
1
1
BIT
-1
-1
OFTWARE
Table
EFR
C
ONT
Table 14
18). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
X
X
X
X
0
0
0
1
1
1
1
1
F
BIT
LOW
40
-0
-0
C
No TX and RX flow control (default and reset)
No transmit flow control
Transmit Xon1/Xoff1
Transmit Xon2/Xoff2
Transmit Xon1 and Xon2/Xoff1 and Xoff2
No receive flow control
Receiver compares Xon1/Xoff1
Receiver compares Xon2/Xoff2
Transmit Xon1/ Xoff1,
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
Transmit Xon2/Xoff2,
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
Transmit Xon1 and Xon2/Xoff1 and Xoff2,
Receiver compares Xon1 and Xon2/Xoff1 and Xoff2
No transmit flow control,
Receiver compares Xon1 and Xon2/Xoff1 and Xoff2
ONTROL
for complete selection with FCR bit 4-5 and FCTR
T
RANSMIT AND
F
UNCTIONS
R
ECEIVE
S
OFTWARE
F
LOW
C
REV. 1.2.3
ONTROL