MC33596FJE Freescale Semiconductor, MC33596FJE Datasheet - Page 36

• Manufacturer Part Number: MC33596FJE
• Description: IC RECEIVER UHF PLL TUNED 32LQFP
• Manufacturer: Freescale Semiconductor
• Type: Receiverr

Specifications of MC33596FJE

• Frequency: 304, 315, 426, 434, 868 & 915MHz
• Sensitivity: -104dBm
• Data Rate - Maximum: 22.4 kBaud
• Modulation Or Protocol: FSK, OOK
• Applications: General Data Transfer
• Current - Receiving: 10.3mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 2.7 V ~ 3.6 V, 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Operating Frequency: 915 MHz
• Operating Supply Voltage: 3.3 V or 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Modulation Type: FSK/OOK
• Package Type: LQFP
• Operating Supply Voltage (min): 2.7V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Register Description
If the data manager is disabled, the incoming signal data rate must be lower than or equal to the data
manager maximum data rate.
TRXE (Receiver Enable) enables the whole receiver. This bit must be set to high level if MCU wakes the
MC33956 to enter receive mode.
DME (Data Manager Enable) enables the data manager.
SOE (Strobe Oscillator Enable) enables the strobe oscillator.
Figure 26
OLS (Out of Lock Status) indicates the current status of the PLL.
LVDS (Low Voltage Detection Status) indicates that a low voltage event has occurred when LVDE = 1.
This bit is read-only and is cleared after a read access.
ILA[1:0] (Input Level Attenuation) define the RF input level attenuation.
36
Reset Value
Bit Name
•
•
Access
Low-pass average filter generating the data slicer reference, if DSREF is set
Data manager
0 = standby mode
1 = other modes can be activated
0 = disabled
1 = enabled
0 = disabled
1 = enabled
0 = The PLL is in lock-in range
1 = The PLL is out of lock-in range
0 = No low voltage detected
1 = Low voltage detected
describes configuration register 3, CONFIG3.
DR1
0
0
1
1
AFF1
Bit 7
R/W
DR0
0
0
1
0
1
AFF0
Cut-off Frequency
Bit 6
R/W
0
Table 10. Base Band Parameter Configuration
Data Filter
12 kHz
24 kHz
48 kHz
6 kHz
Bit 5
OLS
Figure 26. CONFIG3 Register
R
1
MC33596 Data Sheet, Rev. 4
LVDS
Bit 4
R
1
Cut-off Frequency
Average Filter
0.5 kHz
1 kHz
2 kHz
4 kHz
Bit 3
ILA1
R/W
0
Bit 2
ILA0
R/W
0
Data Rate Range
Data Manager
16–22.4 kBd
8–10.6 kBd
2–2.8 kBd
4–5.6 kBd
Bit 1
—
—
0
Freescale Semiconductor
Bit 0
—
—
0
Addr
$02