NT30-KBA04 Omron, NT30-KBA04 Datasheet - Page 372
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
NT30-KBA04
Manufacturer Part Number
NT30-KBA04
Description
ANTI GLARE COVER FOR NT31
Manufacturer
Omron
Specifications of NT30-KBA04
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 372 of 466
- Download datasheet (3Mb)
4-2-2 Notes on Using Commands
Outline of Communications
Reference: In the Format sections in the explanations for commands/responses, paren-
theses are used to indicate parts that can under some circumstances be omitted,
and ** is used to indicate the ASCII code (two hexadecimal digits) of the specified
character.
• Pattern when the operation at the PT is notified to the host.
The points that should be observed when using commands are given below.
Method for Specifying Commands
When a personal computer or similar device is used as the host and a high-level
language such as BASIC or C is used for program writing, commands are speci-
fied as ASCII character strings.
Note that in the explanations in this section, parameters are denoted in lower
case characters. When specifying a command, write those parts denoted in up-
per case without modification, for those parts denoted in lower case, write the
numeric values (BCD or hexadecimal) or character string for parameters as
ASCII character strings. Parts in square brackets, such as [ESC] and [CR] each
indicate one control code (the [ESC] code, the [CR] code, etc.).
In the explanations of commands, expressions such as 4 BCD digits and 2 hexa-
decimal digits are used to mean (respectively) the ASCII character string for a
numerical value expressed as four BCD digits and the ASCII character string for
a numerical value expressed as two hexadecimal digits, etc. Do not specify BCD
and hexadecimal data without alteration: always convert it into an ASCII charac-
ter string before transmission.
Example: The format for the numeral value memory table read command is
The following parameters are specified in this format.
m
t
l
s
The character string actually transmitted is as shown below.
Processing Differences According to Command Length
• If a command is too long because it has been incorrectly specified, an error
• If a command is short because it has been incorrectly specified, a communica-
1
1
1
, l
, t
response for a command length error is returned.
tion error (time out) occurs.
, s
2
2
Sometimes multiple responses may be received for one command.
, t
2
[Operation at host]
Notification reception
3
, t
4
shown below.
[ESC]
[ESC]
1B
1B
:
:
:
:
(l1)
* *
52
52
39
R
R
9
1
0123
99
24
(l2)
* *
4E
4E
39
M
N
9
(1 BCD digit)
(4 BCD digits)
(2 BCD digits)
(2 hexadecimal digits)
(s1)
* *
* *
31
32
m
1
2
Notify Command
(s2)
* *
* *
30
34
t1
0
4
[CR]
[CR]
* *
0D
31
0D
t2
1
* *
32
t3
[Operation at PT]
2
Notify Command
Transmission
* *
33
t4
3
Section
363
4-2
Related parts for NT30-KBA04
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NT30-KBA01](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
CHEMICAL RESISTANT COVER FOR NT31
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: