ATA6603-EK Atmel, ATA6603-EK Datasheet - Page 175
ATA6603-EK
Manufacturer Part Number
ATA6603-EK
Description
MCU, MPU & DSP Development Tools Demoboard LIN-MCM
Manufacturer
Atmel
Datasheet
1.ATA6603P-PLQW.pdf
(360 pages)
Specifications of ATA6603-EK
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 175 of 360
- Download datasheet (6Mb)
4.15.8.2
4921E–AUTO–09/09
Timer/Counter Control Register B – TCCR2B
• Bit 7 – FOC2A: Force Output Compare A
• Bit 6 – FOC2B: Force Output Compare B
• Bits 5:4 – Res: Reserved Bits
• Bit 3 – WGM22: Waveform Generation Mode
• Bit 2:0 – CS22:0: Clock Select
Initial Value
Read/Write
The FOC2A bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR2B is written when operating in PWM mode. When writing a logical one to the FOC2A
bit, an immediate Compare Match is forced on the Waveform Generation unit. The OC2A
output is changed according to its COM2A1:0 bits setting. Note that the FOC2A bit is imple-
mented as a strobe. Therefore it is the value present in the COM2A1:0 bits that determines
the effect of the forced compare.
A FOC2A strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR2A as TOP.
The FOC2A bit is always read as zero.
The FOC2B bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR2B is written when operating in PWM mode. When writing a logical one to the FOC2B
bit, an immediate Compare Match is forced on the Waveform Generation unit. The OC2B
output is changed according to its COM2B1:0 bits setting. Note that the FOC2B bit is imple-
mented as a strobe. Therefore it is the value present in the COM2B1:0 bits that determines
the effect of the forced compare.
A FOC2B strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR2B as TOP.
The FOC2B bit is always read as zero.
These bits are reserved bits in the ATA6602/ATA6603 and will always read as zero.
See the description in
The three Clock Select bits select the clock source to be used by the Timer/Counter (see
Table 4-65 on page
Bit
FOC2A
W
7
0
FOC2B
176).
“Timer/Counter Control Register A – TCCR2A” on page
W
6
0
R
5
–
0
R
4
–
0
WGM22
R
3
0
ATA6602/ATA6603
CS22
R
2
0
CS21
R/W
1
0
CS20
R/W
0
0
172.
TCCR2B
175
Related parts for ATA6603-EK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microcontroller With Lin Transceiver, 5v Regulator And Watchdog
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: