AT85C5122D-SISUM Atmel, AT85C5122D-SISUM Datasheet - Page 140
AT85C5122D-SISUM
Manufacturer Part Number
AT85C5122D-SISUM
Description
RFID Modules & Development Tools 3-5.5V Smart Card Reader
Manufacturer
Atmel
Datasheet
1.AT85C5122D-SISUM.pdf
(213 pages)
Specifications of AT85C5122D-SISUM
Product
RFID Readers
- Current page: 140 of 213
- Download datasheet (3Mb)
Master Mode
Slave Mode
Transmission Formats
140
AT8xC5122/23
Figure 85. Full-duplex Master-Slave Interconnection
The SPI operates in Master mode when the Master bit, MSTR
is set. Only one Master SPI device can initiate transmissions. Software begins the trans-
mission from a Master SPI module by writing to the Serial Peripheral Data Register
(SPDAT). If the shift register is empty, the byte is immediately transferred to the shift
register. The byte begins shifting out on MOSI pin under the control of the serial clock,
SCK. Simultaneously, another byte shifts in from the Slave on the Master’s MISO pin.
The transmission ends when the Serial Peripheral transfer data flag, SPIF, in SPSTA
becomes set. At the same time that SPIF becomes set, the received byte from the Slave
is transferred to the receive data register in SPDAT. Software clears SPIF by reading
the Serial Peripheral Status register (SPSTA) with the SPIF bit set, and then reading the
SPDAT.
When the pin SS is pulled down during a transmission, the data is interrupted and when
the transmission is established again, the data present in the SPDAT is resent.
The SPI operates in Slave mode when the Master bit, MSTR
cleared. Before a data transmission occurs, the Slave Select pin, SS, of the Slave
device must be set to ’0’. SS must remain low until the transmission is complete.
In a Slave SPI module, data enters the shift register under the control of the SCK from
the Master SPI module. After a byte enters the shift register, it is immediately transferred
to the receive data register in SPDAT, and the SPIF bit is set. To prevent an overflow
condition, Slave software must then read the SPDAT before another byte enters the
shift register
least one bus cycle before the Master SPI starts a transmission. If the write to the data
register is late, the SPI transmits the data already in the shift register from the previous
transmission.
Software can select any of four combinations of serial clock (SCK) phase and polarity
using two bits in the SPCON: the Clock Polarity (CPOL
(CPHA
effect on the transmission format. CPHA defines the edges on which the input data are
sampled and the edges on which the output data are shifted (Figure 86 and Figure 87).
The clock phase and polarity should be identical for the Master SPI device and the com-
municating Slave device.
3.
4.
5.
6.
Clock Generator
(4)
SPI
The SPI module should be configured as a Master before it is enabled (SPEN set). Also
the Master SPI should be configured before the Slave SPI.
The SPI module should be configured as a Slave before it is enabled (SPEN set).
The maximum frequency of the SCK for an SPI configured as a Slave is the bus clock
speed.
Before writing to the CPOL and CPHA bits, the SPI should be disabled (SPEN = ’0’).
). CPOL defines the default SCK line level in idle state. It has no significant
Master MCU
(5)
. A Slave SPI must complete the write to the SPDAT (shift register) at
8-bit Shift Register
MOSI
SCK
SS
MISO
VDD
MOSI
MISO
SCK
VSS
SS
8-bit Shift Register
Slave MCU
(4)
(6)
(3)
, in the SPCON register is
) and the Clock Phase
, in the SPCON register
4202E–SCR–06/06
Related parts for AT85C5122D-SISUM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit Microcontrollers - MCU RAM Indus
Manufacturer:
Atmel
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: