AT85C5122D-SISUM Atmel, AT85C5122D-SISUM Datasheet - Page 95
AT85C5122D-SISUM
Manufacturer Part Number
AT85C5122D-SISUM
Description
RFID Modules & Development Tools 3-5.5V Smart Card Reader
Manufacturer
Atmel
Datasheet
1.AT85C5122D-SISUM.pdf
(213 pages)
Specifications of AT85C5122D-SISUM
Product
RFID Readers
- Current page: 95 of 213
- Download datasheet (3Mb)
USB Controller
USB Mass Storage Classes
USB Mass Storage Class CBI
Transport
USB Mass Storage Class Bulk-
Only Transport
USB Device Firmware
Upgrade (DFU)
4202E–SCR–06/06
The AT8xC5122D implements a USB device controller supporting Full Speed data
transfer. In addition to the default control endpoint 0, it provides 6 other endpoints, which
can be configured in Control, Bulk, Interrupt or Isochronous modes:
•
•
•
•
This allows the firmware to be developed conforming to most USB device classes, for
example:
•
•
•
•
Within the CBI framework, the Control endpoint is used to transport command blocks as
well as to transport standard USB requests. One Bulk-Out endpoint is used to transport
data from the host to the device. One Bulk-In endpoint is used to transport data from the
device to the host. And one interrupt endpoint may also be used to signal command
completion (protocol 0); it is optional and may not be used (protocol 1).
The following configuration adheres to these requirements:
•
•
•
•
Within the Bulk-Only framework, the Control endpoint is only used to transport class-
specific and standard USB requests for device set-up and configuration. One Bulk-Out
endpoint is used to transport commands and data from the host to the device. One Bulk-
In endpoint is used to transport status and data from the device to the host. No interrupt
endpoint is needed.
The following configuration adheres to these requirements:
•
•
•
The USB Device Firmware Update (DFU) protocol can be used to upgrade the on-chip
program memory of the AT8xC5122D. This allows the implementation of product
enhancements and patches to devices that are already in the field. Two different config-
urations and description sets are used to support DFU functions. The Run-Time
configuration co-exists with the usual functions of the device, which may be USB Mass
Storage for the AT8xC5122D. It is used to initiate DFU from the normal operating mode.
The DFU configuration is used to perform the firmware update after device re-configura-
tion and USB reset. It excludes any other function. Only the default control pipe
(endpoint 0) is used to support DFU services in both configurations.
USB Mass Storage Class Control/Bulk/Interrupt (CBI) Transport, Revision 1.0 -
December 14, 1998.
USB Mass Storage Class Bulk-Only Transport, Revision 1.0 - September 31, 1999.
USB Human Interface Device Class, Version 1.1 - April 7, 1999.
USB Device Firmware Upgrade Class, Revision 1.0 - May 13, 1999.
Endpoint 0: 8 bytes, Control In-Out
Endpoint 4: 64 bytes, Bulk-Out
Endpoint 5: 64 bytes, Bulk-In
Endpoint 1: 8 bytes, Interrupt In
Endpoint 0: 8 bytes, Control In-Out
Endpoint 4: 64 bytes, Bulk-Out
Endpoint 5: 64 bytes, Bulk-In
Endpoint 0: 32-byte FIFO, default control endpoint
Endpoint 1,2,3: 8-byte FIFO
Endpoint 4,5: 64-byte FIFO
Endpoint 6: 2 x 64-byte Ping-pong FIFO
AT8xC5122/23
95
Related parts for AT85C5122D-SISUM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit Microcontrollers - MCU RAM Indus
Manufacturer:
Atmel
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: