ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 102

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Bit
31:15
23:16
15:8
7:0
ADuC7060/ADuC7061
Table 118. GPxPAR MMR Bit Designations
GP0CON1 Control Registers
The GP0CON1 write values are as follows: GP0KEY1 = 0x7,
GP0CON1 = user value, and GP0KEY2 = 0x13.
Name:
Address:
Default value:
Access:
Function:
Table 119. GP0CON1 Write Sequence
Name
GP0KEY1
GP0CON1
GP0KEY2
Name
GPL[7:0]
GPDS[7:0]
GPPD[7:0]
GP0CON1
0xFFFF0468
0x00
Read and write
This register controls the P0.0, P0.1, P0.2, and
P0.3 functionality of the multifunction GPIO
pins.
Description
Reserved.
General I/O port pin functionality lock
registers.
GPL[7:0] = 0, normal operation.
GPL[7:0] = 1, for each GPIO pin, if this bit is
set, writing to the corresponding bit in
GPxCON or GPxDAT register bit has no
effect.
Drive strength configuration. This bit is
configurable.
GPDS[x] = 0, maximum source current is 2 mA.
GPDS[x] = 1, maximum source current is 4 mA.
Pull-Up Disable Port x[7:0].
GPPD[x] = 0, pull-up resistor is active.
GPPD[x] = 1, pull-up resistor is disabled.
Value
0x7
User value
0x13
Rev. B | Page 102 of 108
Table 120. GP0CON1 MMR Bit Designations
Bit
7:2
1
0
Name
Address:
Default value:
Access:
Function:
Name:
Address:
Default value:
Access:
Function:
Name
Reserve
d
SPII2CS
EL
ADCSEL
GP0KEY1
0xFFFF0464
0xXXXX
Write only
When writing to GP0CON1, the value of 0x07
must be written to this register in the
instruction immediately before writing to
GP0CON1.
GP0KEY2
0xFFFF046C
0xXXXX
Write only
When writing to GP0CON1, the value of 0x13
must be written to this register in the instruction
immediately after writing to GP0CON1.
Description
These bits must always be set to 0.
This bit configures the P0.0 to P0.3 functions
in I
must be set to 0 for this bit to work.
To select the P0.0, P0.1, P0.2, and P0.3
functions in SPI mode, clear this bit to 0.
To select the P0.0, P0.1, P0.2, and P0.3
functions in I
This bit is cleared by default.
This bit configures the P0.0 to P0.3 functions
as GPIO pins or as ADC input pins.
To enable P0.0, P0.1, P0.2 and P0.3 functions
as ADC inputs, set this bit to 1.
To enable P0.0, P0.1, P0.2, and P0.3 functions
as digital I/O, clear this bit to 0.
This bit is cleared by default.
2
C or SPI mode. Note that Bit 0 of GP0CON1
2
C mode, set this bit to 1.