ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 96

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ADuC7060/ADuC7061
SPI REGISTERS
The following MMR registers control the SPI interface: SPISTA, SPIRX, SPITX, SPIDIV, and SPICON.
SPI Status Register
SPISTA Register
Name:
Address:
Default value:
Access:
Function:
Table 106. SPISTA MMR Bit Designations
Bit
15:12
11
10:8
7
6
5
4
3:1
0
Name
SPIREX
SPIRXFSTA[2:0]
SPIFOF
SPIRXIRQ
SPITXIRQ
SPITXUF
SPITXFSTA[2:0]
SPIISTA
SPISTA
0xFFFF0A00
0x00000000
Read only
This 32-bit MMR contains the status of the SPI interface in both master and slave modes.
Description
Reserved bits.
SPI receive FIFO excess bytes present. This bit is set when there are more bytes in the receive FIFO than
indicated in the SPIMDE bits in SPICON.
This bit is cleared when the number of bytes in the FIFO is equal to or less than the number in SPIMDE.
SPI receive FIFO status bits.
[000] = receive FIFO is empty.
[001] = 1 valid byte in the FIFO.
[010] = 2 valid bytes in the FIFO.
[011] = 3 valid bytes in the FIFO.
[100] = 4 valid bytes in the FIFO.
SPI receive FIFO overflow status bit.
Set when the receive FIFO was already full when new data was loaded to the FIFO. This bit generates an
interrupt except when SPIRFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI receive IRQ status bit.
Set when a receive interrupt occurs. This bit is set when SPITMDE in SPICON is cleared and the required
number of bytes has been received.
Cleared when the SPISTA register is read.
SPI transmit IRQ status bit.
Set when a transmit interrupt occurs. This bit is set when SPITMDE in SPICON is set and the required number
of bytes has been transmitted.
Cleared when the SPISTA register is read.
SPI transmit FIFO underflow.
This bit is set when a transmit is initiated without any valid data in the transmit FIFO. This bit generates an
interrupt except when SPITFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI transmit FIFO status bits.
[000] = transmit FIFO is empty.
[001] = 1 valid bytes in the FIFO.
[010] = 2 valid bytes in the FIFO.
[011] = 3 valid bytes in the FIFO.
[100] = 4 valid bytes in the FIFO.
SPI interrupt status bit.
Set to 1 when an SPI based interrupt occurs.
Cleared after reading SPISTA.
Rev. B | Page 96 of 108