ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 93

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Bit
2
1
0
I
Name:
Address:
Default value:
Access:
Function:
I
Name:
Address:
Default value:
Access:
Function:
2
2
C Slave Receive, I2CSRX, Register
C Slave Transmit, I2CSTX, Register
Name
I2CSTXQ
I2CSTFE
I2CETSTA
I2CSRX
0x00
Read only
I2CSTX
0x00
Write only
register.
0xFFFF0930
This 8-bit MMR is the I
0xFFFF0934
This 8-bit MMR is the I
I
I
I
Description
This bit is set to 1 when the slave receives a matching address followed by a read. If the I2CSETEN bit in I2CSCON
is =0, this bit goes high just after the negative edge of SCL during the read bit transmission. If the I2CSETEN bit in
I2CSCON is =1, this bit goes high just after the positive edge of SCL during the read bit transmission. This bit
causes an interrupt to occur if the I2CSTXENI bit in I2CSCON is set.
This bit is cleared in all other conditions.
This bit goes high if the transmit FIFO is empty when a master requests data from the slave. This bit is asserted at
the rising edge of SCL during the read bit.
This bit is cleared in all other conditions.
If the I2CSETEN bit in I2CSCON is =0, this bit goes high if the slave transmit FIFO is empty. If the I2CSETEN bit in
I2CSCON = 1, this bit goes high just after the positive edge of SCL during the write bit transmission. This bit
asserts once only for a transfer.
This bit is cleared after being read.
2
2
2
C slave transmit request bit.
C slave FIFO underflow status bit.
C slave early transmit FIFO status bit.
2
2
C slave receive register.
C slave transmit
Rev. B | Page 93 of 108
I
Name:
Address:
Default value:
Access:
Function:
I
Name:
Addresses:
Default value:
Access:
Function:
2
2
C Hardware General Call Recognition, I2CALT, Register
C Slave Device ID, I2CIDx, Registers
I2CALT
0xFFFF0938
0x00
Read and write
This 8-bit MMR is used with hardware general
calls when the I2CSCON Bit 3 is set to 1. This
register is used in cases where a master is
unable to generate an address for a slave and,
instead, the slave must generate the address for
the master.
I2CIDx
0xFFFF093C = I2CID0
0xFFFF0940 = I2CID1
0xFFFF0944 = I2CID2
0xFFFF0948 = I2CID3
0x00
Read and write
These 8-bit MMRs are programmed with the
I
Addresses section for further details.
2
C bus IDs of the slave. See the I2C Bus
ADuC7060/ADuC7061