XC3S500E-4FT256I Xilinx Inc, XC3S500E-4FT256I Datasheet - Page 107

• Manufacturer Part Number: XC3S500E-4FT256I
• Description: FPGA Spartan®-3E Family 500K Gates 10476 Cells 572MHz 90nm (CMOS) Technology 1.2V 256-Pin FTBGA
• Manufacturer: Xilinx Inc
• Series: Spartan™-3Er

Specifications of XC3S500E-4FT256I

• Package: 256FTBGA
• Family Name: Spartan®-3E
• Device Logic Cells: 10476
• Device Logic Units: 1164
• Device System Gates: 500000
• Number Of Registers: 9312
• Maximum Internal Frequency: 572 MHz
• Typical Operating Supply Voltage: 1.2 V
• Maximum Number Of User I/os: 190
• Ram Bits: 368640
• Number Of Logic Elements/cells: 10476
• Number Of Labs/clbs: 1164
• Total Ram Bits: 368640
• Number Of I /o: 190
• Number Of Gates: 500000
• Voltage - Supply: 1.14 V ~ 1.26 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 256-LBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Start-Up
At the end of configuration, the FPGA automatically pulses
the Global Set/Reset (GSR) signal, placing all flip-flops in a
known state. After configuration completes, the FPGA
switches over to the user application loaded into the FPGA.
The sequence and timing of how the FPGA switches over is
programmable as is the clock source controlling the
sequence.
The default start-up sequence appears in
the Global Three-State signal (GTS) is released one clock
cycle after DONE goes High. This sequence allows the
DONE signal to enable or disable any external logic used
during configuration before the user application in the FPGA
starts driving output signals. One clock cycle later, the Glo-
bal Write Enable (GWE) signal is released. This allows sig-
nals to propagate within the FPGA before any clocked
storage elements such as flip-flops and block ROM are
enabled.
The function of the dual-purpose I/O pins
VS[2:0], HSWAP, and A[23:0]
DONE pin goes High. When DONE is High, these pins
become user I/Os. Like all user-I/O pins, GTS controls when
the dual-purpose pins can drive out.
DS312-2 (v3.8) August 26, 2009
Product Specification
R
,
also changes when the
,
Figure
such as M[2:0],
69, where
www.xilinx.com
The relative timing of configuration events is programmed
via the Bitstream Generator (BitGen) options in the Xilinx
development software. For example, the GTS and GWE
events can be programmed to wait for all the DONE pins to
High on all the devices in a multiple-FPGA daisy-chain, forc-
ing the FPGAs to start synchronously. Similarly, the start-up
sequence can be paused at any stage, waiting for selected
DCMs to lock to their respective input clock signals. See
also
By default, the start-up sequence is synchronized to CCLK.
Alternatively, the start-up sequence can be synchronized to
a user-specified clock from within the FPGA application
using the STARTUP_SPARTAN3E library primitive and by
setting the
FPGA application can optionally assert the GSR and GTS
signals via the STARTUP_SPARTAN3E primitive. For JTAG
configuration, the start-up sequence can be synchronized
to the TCK clock input.
Stabilizing DCM Clocks Before User
Start-Up Clock
Start-Up Clock
Figure 69: Default Start-Up Sequence
DONE
DONE
Phase
Phase
StartupClk
GWE
GWE
GTS
GTS
DONE High
0
0
bitstream generator option. The
1
1
Default Cycles
Sync-to-DONE
2
2
3
3
Functional Description
4
4
5
5
DS312-2_60_022305
Mode.
6 7
6 7
107