MC68SEC000AA16 Freescale Semiconductor, MC68SEC000AA16 Datasheet - Page 124

• Manufacturer Part Number: MC68SEC000AA16
• Description: IC MPU 32BIT 16MHZ 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: M68000r

Specifications of MC68SEC000AA16

• Processor Type: M680x0 32-Bit
• Speed: 16MHz
• Voltage: 3.3V, 5V
• Mounting Type: Surface Mount
• Package / Case: 64-QFP
• Processor Series: M680xx
• Core: CPU32
• Maximum Clock Frequency: 16 MHz
• Operating Supply Voltage: 3.3 V, 5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Core Size: 32 Bit
• Cpu Speed: 16MHz
• Digital Ic Case Style: QFP
• No. Of Pins: 64
• Supply Voltage Range: 5V
• Operating Temperature Range: 0°C To +70°C
• Frequency Typ: 20MHz
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Clock Frequency: 16MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MSTR — Master Mode Select Bit
CPOL — Clock Polarity Bit
CPHA — Clock Phase Bit
SPR[1:0] — SPI Clock Rate Select Bits
8.7.2 Serial Peripheral Status Register
SPIF — SPI Interrupt Complete Flag
WCOL — Write Collision Bit
124
Serial Peripheral Interface (SPI)
It is customary to have an external pullup resistor on lines that are driven by open-drain devices.
When the clock polarity bit is cleared and data is not being transferred, the SCK pin of the master
device has a steady state low value. When CPOL is set, SCK idles high. Refer to
Clock Phase and Polarity
The clock phase bit, in conjunction with the CPOL bit, controls the clock-data relationship between
master and slave. The CPHA bit selects one of two different clocking protocols. Refer to
and
These two bits select the SPI clock (SCK) rate when the device is configured as master. When the
device is configured as slave, these bits have no effect. Refer to
SPIF is set upon completion of data transfer between the processor and the external device. If SPIF
goes high, and if SPIE is set, a serial peripheral interrupt is generated. To clear the SPIF bit, read the
SPSR with SPIF set, then access the SPDR. Unless SPSR is read (with SPIF set) first, attempts to
write SPDR are inhibited.
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by an access
of SPDR. Refer to
0 = Slave mode
1 = Master mode
0 = No write collision
1 = Write collision
8.4 Clock Phase and Polarity
SPR[1:0]
Address:
0 0
0 1
1 0
1 1
Reset:
Read:
Write:
8.5.4 Slave Select
E Clock By
$1029
SPIF
Bit 7
Figure 8-4. Serial Peripheral Status Register (SPSR)
Divide
0
16
32
2
4
Controls.
= Unimplemented
WCOL
6
0
M68HC11E Family Data Sheet, Rev. 5.1
Frequency at
E = 1 MHz
Controls.
62.5 kHz
31.3 kHz
Table 8-1. SPI Clock Rates
500 kHz
250 kHz
(Baud)
and
5
0
8.6 SPI System
MODF
Frequency at
4
0
E = 2 MHz
62.5 kHz
1.0 MHz
500 kHz
125 kHz
(Baud)
3
0
Errors.
Frequency at
E = 3 MHz (
187.5 kHz
93.8 kHz
1.5 MHz
750 kHz
Table
Baud)
2
0
8-1.
1
0
Frequency at
E = 4 MHz
250 kHz
125 kHz
(Baud)
2 MHz
1 MHz
Freescale Semiconductor
Figure 8-2
Bit 0
0
Figure 8-2
and
8.4