MC68MH360EM33L Freescale Semiconductor, MC68MH360EM33L Datasheet - Page 513

• Manufacturer Part Number: MC68MH360EM33L
• Description: IC MPU QUICC ETHER 33MHZ 240FQFP
• Manufacturer: Freescale Semiconductor

Specifications of MC68MH360EM33L

• Processor Type: M683xx 32-Bit
• Speed: 33MHz
• Voltage: 5V
• Mounting Type: Surface Mount
• Package / Case: 240-FQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -

7.10.17.15 SCC HDLC EXAMPLE #2. •The following is an initialization sequence for an
7.10.18 HDLC Bus Controller
HDLC bus is an enhancement of HDLC that allows an HDLC-based LAN and other HDLC
point-to-multipoint configurations to be easily implemented. Most versions of HDLC-based
controllers only provide point-to-point communications.
MOTOROLA
26. Set the PSMR4 to $0000 to configure one opening and one closing flag, 16-bit
27. Write $00000030 to GSMR_L4 to enable the SCC4 transmitter and receiver. This
1. Follow all the steps in the HDLC Example #1, until the step where the GSMR is initial-
2. Write $00000000 to GSMR_H4 to enable normal behavior of the CTS and CD pins,
3. Write $004AA400 to GSMR_L4 to configure carrier sense always active, a 16-bit pre-
4. Set the PSMR4 to $0000 to configure one opening and one closing flag, 16-bit CCITT-
5. Write $004AA430 to GSMR_L4 to enable the SCC4 transmitter and receiver. This ad-
SCC HDLC channel that uses the DPLL in a Manchester encoding. The user provides
a clock that is 16x the desired bit rate, on the CLK7 pin. CLK7 is then connected to the
HDLC transmitter and receiver. (A baud rate generator could have been used instead,
if desired). SCC4 is used. The HDLC controller is configured with the RTS4, CTS4, and
CD4 pins active.
is desired, set the RINV and TINV bits.
CCITT-CRC, and prevention of multiple frames in the FIFO.
additional write ensures that the ENT and ENR bits will be enabled last.
ized.
and idles between frames (as opposed to flags).
amble of "01" pattern, 16x operation of the DPLL for the receiver and transmitter,
Manchester encoding for the receiver and transmitter, the CTS and CD pins to auto-
matically control transmission and reception (DIAG bits), and the HDLC mode. Notice
that the transmitter (ENT) and receiver (ENR) have not been enabled yet.
CRC, and not allowing multiple frames in the FIFO.
ditional write ensures that the ENT and ENR bits will be enabled last.
After 5 bytes and CRC have been transmitted, the Tx BD is
closed. Additionally, the receive buffer is closed after a frame is
received. Any additional receive data beyond 256 bytes or a sin-
gle frame will cause a busy (out-of-buffers) condition since only
one Rx BD was prepared.
After the preamble and 5 bytes have been transmitted, the Tx
BD is closed. Additionally, the receive buffer is closed after 16
bytes have been received. Any additional receive data beyond
16 bytes will cause a busy (out-of-buffers) condition since only
one Rx BD was prepared.
Freescale Semiconductor, Inc.
For More Information On This Product,
MC68360 USER’S MANUAL
Go to: www.freescale.com
NOTE
NOTE
Serial Communication Controllers (SCCs)
7-189