PIC18F4550-I/P Microchip Technology Inc., PIC18F4550-I/P Datasheet - Page 272

• Manufacturer Part Number: PIC18F4550-I/P
• Description: 40 PIN, 32 KB FLASH, 2048 RAM, FS-USB 2.0
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4550-I/P

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 12 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 34
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Ram Size: 2K Bytes
• Speed: 48 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F2455/2550/4455/4550
22.1
There are eight modes of operation for the compara-
tors, shown in Figure 22-1. Bits CM2:CM0 of the
CMCON register are used to select these modes. The
TRISA register controls the data direction of the
comparator pins for each mode. If the Comparator
FIGURE 22-1:
DS39632C-page 270
Comparators Reset
CM2:CM0 = 000
Two Independent Comparators
CM2:CM0 = 010
Two Common Reference Comparators
CM2:CM0 = 100
One Independent Comparator with Output
CM2:CM0 = 001
A = Analog Input, port reads zeros always
* Setting the TRISA<5:4> bits will disable the comparator outputs by configuring the pins as inputs.
RA4/T0CKI/C1OUT*/RCV
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
REF
REF
REF
REF
REF
REF
REF
REF
+
-/CV
+
-/CV
+
-/CV
+
-/CV
Comparator Configuration
REF
REF
REF
REF
A
A
A
A
A
A
A
A
A
A
A
D
A
A
D
D
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
COMPARATOR I/O OPERATING MODES
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
C1
C2
C1
C2
C1
C2
C1
C2
Off (Read as ‘0’)
Off (Read as ‘0’)
C1OUT
C2OUT
C1OUT
C2OUT
C1OUT
Off (Read as ‘0’)
D = Digital Input
Preliminary
Two Common Reference Comparators with Outputs
CM2:CM0 = 101
Two Independent Comparators with Outputs
CM2:CM0 = 011
Comparators Off (POR Default Value)
CM2:CM0 = 111
Four Inputs Multiplexed to Two Comparators
CM2:CM0 = 110
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
RA0/AN0
RA3/AN3/
V
RA4/T0CKI/C1OUT*/RCV
RA1/AN1
RA2/AN2/
V
RA5/AN4/SS/HLVDIN/C2OUT*
RA0/AN0
RA3/AN3/
V
RA4/T0CKI/C1OUT*/
RCV
RA1/AN1
RA2/AN2/
V
RA5/AN4/SS/HLVDIN/C2OUT*
RA0/AN0
RA3/AN3/
V
RA1/AN1
RA2/AN2/
V
REF
REF
REF
REF
REF
REF
REF
REF
mode is changed, the comparator output level may not
be valid for the specified mode change delay shown in
Section 28.0 “Electrical Characteristics”.
Note:
CIS (CMCON<3>) is the Comparator Input Switch
+
-/CV
+
-/CV
+
-/CV
+
-/CV
REF
REF
REF
REF
A
A
A
A
D
D
D
D
A
A
A
A
Comparator interrupts should be disabled
during a Comparator mode change.
Otherwise, a false interrupt may occur.
A
A
A
D
V
V
V
V
V
V
V
V
CIS = 0
CIS = 1
CIS = 0
CIS = 1
IN
IN
IN
IN
IN
IN
IN
IN
-
+
-
+
-
+
-
+
V
V
V
V
IN
IN
IN
IN
-
+
-
+
© 2006 Microchip Technology Inc.
C1
C2
C1
C2
V
V
V
V
C1
C2
IN
IN
IN
IN
CV
-
+
-
+
REF
C1OUT
C2OUT
Off (Read as ‘0’)
Off (Read as ‘0’)
C1
C2
From V
C1OUT
C2OUT
REF
C1OUT
C2OUT
Module