SC28L202A1DGG/G,11 NXP Semiconductors, SC28L202A1DGG/G,11 Datasheet - Page 37
![IC UART DUAL W/FIFO 56-TSSOP](/photos/6/90/69069/56-tssop_sml.jpg)
SC28L202A1DGG/G,11
Manufacturer Part Number
SC28L202A1DGG/G,11
Description
IC UART DUAL W/FIFO 56-TSSOP
Manufacturer
NXP Semiconductors
Series
IMPACTr
Datasheet
1.SC28L202A1DGG118.pdf
(77 pages)
Specifications of SC28L202A1DGG/G,11
Features
False-start Bit Detection
Number Of Channels
2, DUART
Fifo's
256 Byte
Voltage - Supply
3.3V, 5V
With Parallel Port
Yes
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
56-TFSOP (0.240", 6.10mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935279792118
SC28L202A1DGG/G-T
SC28L202A1DGG/G-T
SC28L202A1DGG/G-T
SC28L202A1DGG/G-T
Philips Semiconductors
XISR – Xon–Xoff Interrupt Status Register A and B (Reading this register clears XISR(7:4))
XISR[7:6] Received X Character Status.
This field can be read to determine if the receiver has encountered a
Xon or Xoff character in the incoming data stream. These bits are
maintained until a read of the XISR. The field is updated by X
character reception regardless of the state of MR3(7) and MR3(3:2)
or IMR(4). The field can therefore be used as a character detector
for the bit patterns stored in the Xon and Xoff Character Registers.
XISR[5:4] Automatic transmission Status.
This field indicates the last flow control character sent in the Auto
Receiver flow control mode. If Auto Receiver mode has not been
enabled, this field will always read b’00. It will likewise reset to b’00 if
MR0(3) is reset. If the Auto Receiver mode is exited while this field
reads b’10, it is the user’s responsibility to transmit a Xon, when
appropriate.
XISR[3:2] TxD Condition of the automatic flow control status.
This field tracks the transmitter’s flow status as follows:
WCXER Watch Dog, Character, Address and X Enable Register – A and B
This register enables the UART’s Character Recognition, Address
Recognition and Receiver watchdog timer. If both enable and
disable are active a disable results. This register is used to enable
the general–purpose character recognition feature WITHOUT
2005 Nov 01
00 – n ormal transmission. Transmitter is not affected by Xon or
Xoff.
01 – TxD halt pending. After the current character finishes the
transmitter will stop. The status will then change to b’11.
Dual UART
Bits 7:6
Received X Character Status
00 = none
01 = Xoff received
10 = Xon received
11 = both received
Bit 7
Watch dog *
1 = disable Wd
0 = no action
Bit 6
1 = enable
Wd
0 = no action
Bits 5:4
Automatic X Character transmission
status
00 = none
01 = Xon transmitted
10 = Xoff transmitted
11 = Both transmitted
Bit 5
Address recognition
1 = disable Ar
0 = no action
Bit 4
1 = enable Ar
0 = no action
31
XISR[1:0] TxD X character Status.
This field allows determination of the type of character being
transmitted. It will always be b’00 if none of the automatic X
character controls of MR3[3:2] is enabled.
Conditions b’10 and b’11 will not exist for more than a character
time.
causing any Xon/Xoff or wakeup mode activities to occur. The
recognition event is reported in the ISR register.
* This bit control is duplicated at MR0[7].
After a read of the XISR, it will return to ‘normal’ status.
10 – r e–enabled. The transmitter had been halted and has been
restarted. It is sending (or is prepared to send) data characters.
11 – The transmitter is stopped due to an Xoff character being
received from its associated receiver. The transmitter is ‘flow
controlled’.
01 – The channel is waiting for a data character to transfer from
the TxFIFO. This condition will only occur for a bit time after a Xon
or Xoff character transmission unless the TxFIFO is empty.
10 – A command to send an Xoff character is pending.
11 – A command to send an Xon character is pending.
BIT 3
Xon recognition
1 = disable
Xon
0 = no action
Bits 3:2
TxD flow status
00 = normal transmission
01 = TxD halt pending
10 = re-enabled
11 = flow halted
BIT 2
1 = enable
Xon
0 = no action
BIT 1
Xoff Recognition
1 = disable
Xoff
0 = no action
Bits 1:0
TxD character status
00 = normal TxD data
01 = Idle wait for FIFO
data
10 = Xoff in pending
11 = Xon in pending
SC28L202
Product data sheet
BIT 0
1 = enable
Xoff
0 = no action