AT32UC3A464S Atmel Corporation, AT32UC3A464S Datasheet - Page 435

• Manufacturer Part Number: AT32UC3A464S
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A464S

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: AES
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.8.12
Name:
Access Type:
Offset:
Reset Value:
• DLYBCT: Delay Between Consecutive Transfers
• DLYBS: Delay Before SPCK
• SCBR: Serial Clock Baud Rate
32072G–11/2011
31
23
15
7
This field defines the delay between two consecutive transfers with the same peripheral without removing the chip select. The
delay is always inserted after each transfer and before removing the chip select if needed.
When DLYBCT equals zero, no delay between consecutive transfers is inserted and the clock keeps its duty cycle over the
character transfers.
Otherwise, the following equation determines the delay:
This field defines the delay from NPCS valid to the first valid SPCK transition.
When DLYBS equals zero, the NPCS valid to SPCK transition is 1/2 the SPCK clock period.
Otherwise, the following equations determine the delay:
In Master Mode, the SPI Interface uses a modulus counter to derive the SPCK baud rate from the CLK_SPI. The Baud rate is
selected by writing a value from 1 to 255 in the SCBR field. The following equations determine the SPCK baud rate:
Writing the SCBR field to zero is forbidden. Triggering a transfer while SCBR is zero can lead to unpredictable results.
At reset, SCBR is zero and the user has to write it to a valid value before performing the first transfer.
If a clock divider (SCBRn) field is set to one and the other SCBR fields differ from one, access on CSn is correct but no correct
access will be possible on other CS.
Delay Between Consecutive Transfers
Delay Before SPCK
SPCK Baudrate
Chip Select Register 3
30
22
14
6
CSR3
Read/Write
0x3C
0x00000000
=
BITS
CLKSPI
---------------------
=
SCBR
-------------------- -
CLKSPI
DLYBS
29
21
13
5
=
32
----------------------------------- -
28
20
12
4
CLKSPI
×
DLYBCT
DLYBCT
DLYBS
SCBR
CSAAT
27
19
11
3
CSNAAT
26
18
10
2
NCPHA
25
17
9
1
CPOL
24
16
8
0
435