AT32UC3A464S Atmel Corporation, AT32UC3A464S Datasheet - Page 666

• Manufacturer Part Number: AT32UC3A464S
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A464S

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: AES
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.8.1
26.8.1.1
Name:
Access Type:
Offset:
Reset Value:
• UIMOD: USBB Mode
• UIDE: USB_ID Pin Enable
• UNLOCK: Timer Access Unlock
• TIMPAGE: Timer Page
• TIMVALUE: Timer Value
• USBE: USBB Enable
32072G–11/2011
USBE
STOE
31
23
15
7
-
-
This bit has no effect when UIDE is one (USB_ID input pin activated).
0: The module is in USB host mode.
1: The module is in USB device mode.
This bit can be written even if USBE is zero or FRZCLK is one. Disabling the USBB (by writing a zero to the USBE bit) does not
reset this bit.
0: The USB mode (device/host) is selected from the UIMOD bit.
1: The USB mode (device/host) is selected from the USB_ID input pin.
This bit can be written even if USBE is zero or FRZCLK is one. Disabling the USBB (by writing a zero to the USBE bit) does not
reset this bit.
1: The TIMPAGE and TIMVALUE fields are unlocked.
0: The TIMPAGE and TIMVALUE fields are locked.
The TIMPAGE and TIMVALUE fields can always be read, whatever the value of UNLOCK.
This field contains the page value to access a special timer register.
This field selects the timer value that is written to the special time register selected by TIMPAGE. See
details.
Writing a zero to this bit will reset the USBB, disable the USB transceiver and, disable the USBB clock inputs. Unless explicitly
stated, all registers then will become read-only and will be reset.
1: The USBB is enabled.
0: The USBB is disabled.
USB General Registers
General Control Register
UNLOCK
FRZCLK
30
22
14
6
-
USBCON
Read/Write
0x0800
0x03004000
ROLEEXE
VBUSPO
29
21
13
5
-
TIMPAGE
OTGPADE
BCERRE
28
20
12
4
-
VBERRE
27
19
11
3
-
-
26
18
10
2
-
-
VBUSTE
UIMOD
25
17
9
1
Section 26.7.1.8
TIMVALUE
VBUSHWC
UIDE
IDTE
24
16
8
0
for
666