AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 91

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.4.3
10.4.4
32099G–06/2011
FLASHCDW
SAU
Transfer error will stall a transmit peripheral handshake interface
If a transfer error is encountered on a channel transmitting to a peripheral, the peripheral
handshake of the active channel will stall and the PDCA will not do any more transfers on
the affected peripheral handshake interface.
Fix/Workaround
Disable and then enable the peripheral after the transfer error.
VERSION register reads 0x120
The VERSION register reads 0x120 instead of 0x122.
Fix/Workaround
None.
Chip Erase
When performing a chip erase, the device may report that it is protected (IR=0x11) and that
the erase failed, even if it was successful.
Fix/Workaround
Perform a reset before any further read and programming.
Fuse Programming
Programming fuses does not work.
Fix/Workaround
Do not program fuses. All fuses will be erased during chip erase command.
Wait 500 ns before reading from the flash after switching read mode
After switching between normal read mode and high-speed read mode, the application must
wait at least 500ns before attempting any access to the flash.
Fix/Workaround
Solution 1: Make sure that the appropriate instructions are executed from RAM, and that a
waiting-loop is executed from RAM waiting 500ns or more before executing from flash.
Solution 2. Execute from flash with a clock with period longer than 500ns. This guarantees
that no new read access is attempted before the flash has had time to settle in the new read
mode.
Flash self programming may fail in one wait state mode
Writes in flash and user pages may fail if executing code is located in address space
mapped to flash, and the flash controller is configured in one wait state mode (the Flash
Wait State bit in the Flash Control Register (FCR.FWS) is one).
Fix/Workaround
Solution 1: Configure the flash controller in zero wait state mode (FCR.FWS=0).
Solution 2: Configure the HMATRIX master 1 (CPU Instruction) to use the unlimited burst
length transfer mode (MCFG1.ULBT=0), and the HMATRIX slave 0 (FLASHCDW) to use
the maximum slot cycle limit (SCFG0.SLOT_CYCLE=255).
VERSION register reads 0x100
The VERSION register reads 0x100 instead of 0x102.
Fix/Workaround
None.
The SR.IDLE bit reads as zero
The IDLE bit in the Status Register (SR.IDLE) reads as zero.
AT32UC3L016/32/64
91