AT90PWM216 Atmel Corporation, AT90PWM216 Datasheet - Page 125

• Manufacturer Part Number: AT90PWM216
• Manufacturer: Atmel Corporation

Specifications of AT90PWM216

• Flash (kbytes): 16 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

15.10 16-bit Timer/Counter Register Description
15.10.1
7710F–AVR–09/11
Timer/Counter1 Control Register A – TCCR1A
Figure 15-13. Timer/Counter Timing Diagram, with Prescaler (f
• Bit 7:6 – COMnA1:0: Compare Output Mode for Channel A
• Bit 5:4 – COMnB1:0: Compare Output Mode for Channel B
The COMnA1:0 and COMnB1:0 control the Output Compare pins (OCnA and OCnB respec-
tively) behavior. If one or both of the COMnA1:0 bits are written to one, the OCnA output
overrides the normal port functionality of the I/O pin it is connected to. If one or both of the
COMnB1:0 bit are written to one, the OCnB output overrides the normal port functionality of the
I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit correspond-
ing to the OCnA or OCnB pin must be set in order to enable the output driver.
When the OCnA or OCnB is connected to the pin, the function of the COMnx1:0 bits is depen-
dent of the WGMn3:0 bits setting.
WGMn3:0 bits are set to a Normal or a CTC mode (non-PWM).
Table 15-2.
Bit
Read/Write
Initial Value
COMnA1/COMnB1
and ICF n
(PC and PFC PWM)
TOVn
(CTC and FPWM)
(Update at TOP)
0
0
1
1
OCRnx
TCNTn
TCNTn
as TOP)
(clk
clk
clk
I/O
(FPWM)
I/O
Tn
/8)
COM1A1
(if used
Compare Output Mode, non-PWM
R/W
7
0
COM1A0
COMnA0/COMnB0
R/W
6
0
TOP - 1
TOP - 1
Old OCRnx Value
0
1
0
1
COM1B1
R/W
Table 15-2
5
0
COM1B0
R/W
4
0
Description
Normal port operation, OCnA/OCnB disconnected.
Toggle OCnA/OCnB on Compare Match.
Clear OCnA/OCnB on Compare Match (Set output to
low level).
Set OCnA/OCnB on Compare Match (Set output to
high level).
shows the COMnx1:0 bit functionality when the
TOP
TOP
R
3
–
0
AT90PWM216/316
BOTTOM
TOP - 1
clk_I/O
R
2
–
0
New OCRnx Value
/8)
WGM11
R/W
1
0
BOTTOM + 1
TOP - 2
WGM10
R/W
0
0
TCCR1A
125