AT90PWM216 Atmel Corporation, AT90PWM216 Datasheet - Page 202

• Manufacturer Part Number: AT90PWM216
• Manufacturer: Atmel Corporation

Specifications of AT90PWM216

• Flash (kbytes): 16 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

18.8.3
7710F–AVR–09/11
Asynchronous Operational Range
point marked (A) in
(B). (C) marks a stop bit of full length. The early start bit detection influences the operational
range of the Receiver.
The operational range of the Receiver is dependent on the mismatch between the received bit
rate and the internally generated baud rate. If the Transmitter is sending frames at too fast or too
slow bit rates, or the internally generated baud rate of the Receiver does not have a similar (see
Table
bit.
The following equations can be used to calculate the ratio of the incoming data rate and internal
receiver baud rate.
Table 1.
D
S
S
S
R
R
Table 18-2
that Normal Speed mode has higher toleration of baud rate variations.
Table 18-2.
F
M
slow
fast
# (Data+Parity Bit)
is the ratio of the fastest incoming data rate that can be accepted in relation to the
18-2) base frequency, the Receiver will not be able to synchronize the frames to the start
R
10
D
slow
5
6
7
8
9
and
Sum of character size and parity size (D = 5 to 10 bit)
Samples per bit. S = 16 for Normal Speed mode and S = 8 for Double Speed
mode.
First sample number used for majority voting. S
for Double Speed mode.
Middle sample number used for majority voting. S
S
is the ratio of the slowest incoming data rate that can be accepted in relation to the
receiver baud rate.
receiver baud rate.
Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode
(U2X = 0)
=
M
Table 18-3
------------------------------------------ -
S 1
= 5 for Double Speed mode.
–
Figure
(
D
+
R
+
D S ⋅
slow
93.20
94.12
94.81
95.36
95.81
96.17
1
18-8. For Double Speed mode the first low level must be delayed to
list the maximum receiver baud rate error that can be tolerated. Note
)S
(%)
+
S
F
R
106.67
105.79
105.11
104.58
104.14
103.78
fast
(%)
Max Total Error (%)
+5.79/-5.88
+5.11/-5.19
+4.58/-4.54
+4.14/-4.19
+3.78/-3.83
+6.67/-6.8
R
fast
AT90PWM216/316
F
= 8 for normal speed and S
=
M
= 9 for normal speed and
-----------------------------------
(
D
(
+
D
1
+
)S
Recommended Max
2
Receiver Error (%)
)S
+
S
M
± 3.0
± 2.5
± 2.0
± 2.0
± 1.5
± 1.5
F
202
= 4