ATmega1280R212 Atmel Corporation, ATmega1280R212 Datasheet - Page 113
ATmega1280R212
Manufacturer Part Number
ATmega1280R212
Description
Manufacturer
Atmel Corporation
Specifications of ATmega1280R212
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
16 MHz
Max I/o Pins
86
Spi
5
Twi (i2c)
1
Uart
4
Adc Channels
16
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
8
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
6
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
- Current page: 113 of 448
- Download datasheet (8Mb)
15.2
15.2.1
2549N–AVR–05/11
Register Description
EICRA – External Interrupt Control Register A
Figure 15-1. Normal pin change interrupt.
The External Interrupt Control Register A contains control bits for interrupt sense control.
• Bits 7:0 – ISC31, ISC30 – ISC00, ISC00: External Interrupt 3 - 0 Sense Control Bits
The External Interrupts 3 - 0 are activated by the external pins INT3:0 if the SREG I-flag and the
corresponding interrupt mask in the EIMSK is set. The level and edges on the external pins that
activate the interrupts are defined in
asynchronously. Pulses on INT3:0 pins wider than the minimum pulse width given in
on page 114
rupt. If low level interrupt is selected, the low level must be held until the completion of the
currently executing instruction to generate an interrupt. If enabled, a level triggered interrupt will
generate an interrupt request as long as the pin is held low. When changing the ISCn bit, an
interrupt can occur. Therefore, it is recommended to first disable INTn by clearing its Interrupt
Enable bit in the EIMSK Register. Then, the ISCn bit can be changed. Finally, the INTn interrupt
flag should be cleared by writing a logical one to its Interrupt Flag bit (INTFn) in the EIFR Regis-
ter before the interrupt is re-enabled.
PCINT(0)
Bit
(0x69)
Read/Write
Initial Value
pcint_setflag
pcint_in_(n)
clk
PCINT(n)
pcint_syn
pin_sync
pin_lat
PCIF
will generate an interrupt. Shorter pulses are not guaranteed to generate an inter-
LE
clk
ISC31
R/W
7
0
pin_lat
D
Q
ISC30
R/W
pin_sync
PCINT(0) in PCMSK(x)
6
0
ATmega640/1280/1281/2560/2561
ISC21
pcint_in_(0)
R/W
5
0
Table 15-1 on page
ISC20
R/W
4
0
0
x
clk
ISC11
R/W
3
0
114. Edges on INT3:0 are registered
pcint_syn
ISC10
R/W
2
0
ISC01
pcint_setflag
R/W
1
0
ISC00
R/W
0
0
PCIF
Table 15-2
EICRA
113
Related parts for ATmega1280R212
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika