ATmega1280R212 Atmel Corporation, ATmega1280R212 Datasheet - Page 61
ATmega1280R212
Manufacturer Part Number
ATmega1280R212
Description
Manufacturer
Atmel Corporation
Specifications of ATmega1280R212
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
16 MHz
Max I/o Pins
86
Spi
5
Twi (i2c)
1
Uart
4
Adc Channels
16
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
8
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
6
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
- Current page: 61 of 448
- Download datasheet (8Mb)
12.2.2
12.2.3
2549N–AVR–05/11
External Reset
Brown-out Detection
Figure 12-3. MCU Start-up, RESET Extended Externally
An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the
minimum pulse width (see
reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset.
When the applied signal reaches the Reset Threshold Voltage – V
delay counter starts the MCU after the Time-out period – t
Figure 12-4. External Reset During Operation
ATmega640/1280/1281/2560/2561 has an On-chip Brown-out Detection (BOD) circuit for moni-
toring the V
the BOD can be selected by the BODLEVEL Fuses. The trigger level has a hysteresis to ensure
spike free Brown-out Detection. The hysteresis on the detection level should be interpreted as
V
When the BOD is enabled, and V
12-5 on page
trigger level (V
out period t
The BOD circuit will only detect a drop in V
ger than t
BOT+
INTERNAL
TIME-OUT
= V
RESET
RESET
BOD
BOT
V
CC
TOUT
CC
CC
+ V
given in
62), the Brown-out Reset is immediately activated. When V
BOT+
level during operation by comparing it to a fixed trigger level. The trigger level for
has expired.
HYST
in
/2 and V
Figure 12-5 on page
“System and Reset Characteristics” on page
V
“System and Reset Characteristics” on page
POT
BOT-
ATmega640/1280/1281/2560/2561
CC
= V
decreases to a value below the trigger level (V
BOT
- V
62), the delay counter starts the MCU after the Time-
CC
HYST
if the voltage stays below the trigger level for lon-
V
RST
/2.
t
TOUT
TOUT
– has expired.
RST
372.
– on its positive edge, the
CC
372) will generate a
increases above the
BOT-
in
Figure
61
Related parts for ATmega1280R212
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika