ATmega1280R212 Atmel Corporation, ATmega1280R212 Datasheet - Page 207

• Manufacturer Part Number: ATmega1280R212
• Manufacturer: Atmel Corporation

Specifications of ATmega1280R212

• Flash (kbytes): 128 Kbytes
• Max. Operating Frequency: 16 MHz
• Max I/o Pins: 86
• Spi: 5
• Twi (i2c): 1
• Uart: 4
• Adc Channels: 16
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: AES
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 6
• Frequency Band: 700/800/900MHz
• Max Data Rate (mb/s): 1
• Antenna Diversity: No
• External Pa Control: Yes
• Power Output (dbm): 10
• Receiver Sensitivity (dbm): -110
• Receive Current Consumption (ma): 9.0
• Transmit Current Consumption (ma): 18 at 5dBm
• Link Budget (dbm): 120

22.2.1
2549N–AVR–05/11
Internal Clock Generation – The Baud Rate Generator
UCSRnA Register. When using synchronous mode (UMSELn = 1), the Data Direction Register
for the XCKn pin (DDR_XCKn) controls whether the clock source is internal (Master mode) or
external (Slave mode). The XCKn pin is only active when using synchronous mode.
Figure 22-2
Figure 22-2. Clock Generation Logic, Block Diagram
Signal description:
Internal clock generation is used for the asynchronous and the synchronous master modes of
operation. The description in this section refers to
The USART Baud Rate Register (UBRRn) and the down-counter connected to it function as a
programmable prescaler or baud rate generator. The down-counter, running at system clock
(f
the UBRRLn Register is written. A clock is generated each time the counter reaches zero. This
clock is the baud rate generator clock output (= f
baud rate generator clock output by 2, 8 or 16 depending on mode. The baud rate generator out-
put is used directly by the Receiver’s clock and data recovery units. However, the recovery units
use a state machine that uses 2, 8 or 16 states depending on mode set by the state of the
UMSELn, U2Xn and DDR_XCKn bits.
Table 22-1 on page 208
for calculating the UBRRn value for each mode of operation using an internally generated clock
source.
osc
), is loaded with the UBRRn value each time the counter has counted down to zero or when
txclk
rxclk
xcki
xcko
f
OSC
DDR_XCK
XCK
Pin
shows a block diagram of the clock generation logic.
xcko
xcki
OSC
operation.
operation.
Transmitter clock (Internal Signal).
Receiver base clock (Internal Signal).
Input from XCK pin (internal Signal). Used for synchronous slave
Clock output to XCK pin (Internal Signal). Used for synchronous master
XTAL pin frequency (System Clock).
Down-Counter
Prescaling
contains equations for calculating the baud rate (in bits per second) and
Register
UBRR
Sync
ATmega640/1280/1281/2560/2561
UBRR+1
fosc
Detector
UCPOL
Edge
/2
Figure
osc
/(UBRRn+1)). The Transmitter divides the
/4
22-2.
/2
DDR_XCK
U2X
0
1
0
1
0
1
1
0
UMSEL
txclk
rxclk
207