ATmega1280R212 Atmel Corporation, ATmega1280R212 Datasheet - Page 373

• Manufacturer Part Number: ATmega1280R212
• Manufacturer: Atmel Corporation

Specifications of ATmega1280R212

• Flash (kbytes): 128 Kbytes
• Max. Operating Frequency: 16 MHz
• Max I/o Pins: 86
• Spi: 5
• Twi (i2c): 1
• Uart: 4
• Adc Channels: 16
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: AES
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 6
• Frequency Band: 700/800/900MHz
• Max Data Rate (mb/s): 1
• Antenna Diversity: No
• External Pa Control: Yes
• Power Output (dbm): 10
• Receiver Sensitivity (dbm): -110
• Receive Current Consumption (ma): 9.0
• Transmit Current Consumption (ma): 18 at 5dBm
• Link Budget (dbm): 120

31.5.2
Table 31-6.
Note:
31.6
2549N–AVR–05/11
1. V
2-wire Serial Interface Characteristics
Enhanced Power-On Reset
tested down to V
a voltage where correct operation of the microcontroller is no longer guaranteed. The test is performed using
BODLEVEL = 110 for 4MHz operation of ATmega640V/1280V/1281V/2560V/2561V, BODLEVEL = 101 for 8MHz operation
of ATmega640V/1280V/1281V/2560V/2561V and ATmega640/1280/1281, and BODLEVEL = 100 for 16MHz operation of
ATmega640/1280/1281/2560/2561.
BOT
BODLEVEL Fuse Coding
BODLEVEL 2:0 Fuses
may be below nominal minimum operating voltage for some devices. For devices where this is the case, the device is
111
110
101
100
011
010
001
000
CC
T h i s
ATmega640/1280/1281/2560/2561. The table below describes the characteristics of this power-
on reset and it is valid for the following devices only:
•
•
•
•
•
Table 31-5.
Notes:
Table 31-7 on page 374
Bus. The ATmega640/1280/1281/2560/2561 2-wire Serial Interface meets or exceeds these
requirements under the noted conditions.
Timing symbols refer to
Symbol
V
V
= V
POT
PSR
ATmega640: revision B and newer
ATmega1280: revision B and newer
ATmega1281: revision B and newer
ATmega2560: revision F and newer
ATmega2561: revision F and newer
BOT
i m p l e m e n t a t i o n
1. Values are guidelines only.
2. Threshold where device is released from reset when voltage is rising.
3. The power-on reset threshold voltage (falling) will not work unless the supply voltage has been
during the production test. This guarantees that a Brown-Out Reset will occur before V
below V
Parameter
Power-on Reset Threshold Voltage (rising)
Power-on Reset Threshold Voltage (falling)
Power-On Slope Rate
(1)
Characteristics of Enhanced Power-On Reset. T
POT
.
Figure 31-6 on page
describes the requirements for devices connected to the 2-wire Serial
o f
Min V
ATmega640/1280/1281/2560/2561
p o w e r - o n
1.7
2.5
4.1
BOT
375.
r e s e t
(2)
(3)
Typ V
BOD Disabled
1.8
2.7
4.3
e x i s t s
Reserved
BOT
Min.
0.01
1.1
0.6
(1)
A
= -40 to +85°C.
i n
Typ.
Max V
n e w e r
1.4
1.3
2.0
2.9
4.5
(1)
BOT
Max.
v e r s i o n s
1.6
1.6
(1)
CC
Units
V
drops to
Units
V/ms
V
V
373
o f