ATmega168 Atmel Corporation, ATmega168 Datasheet - Page 292
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega168
Manufacturer Part Number
ATmega168
Description
Manufacturer
Atmel Corporation
Specifications of ATmega168
Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA168
Manufacturer:
AVAILINK
Quantity:
1 590
Company:
Part Number:
ATmega168-15AD
Manufacturer:
VISHAY
Quantity:
15 600
Part Number:
ATmega168-15AT1
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega168-15MT
Manufacturer:
ATMEL
Quantity:
686
Part Number:
ATmega168-15MT
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega168-15MT1
Manufacturer:
ATMEL
Quantity:
372
Part Number:
ATmega168-15MZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega168-20AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
28.7.2
28.7.3
28.7.4
2545T–AVR–05/11
Considerations for efficient programming
Chip erase
Programming the flash
4. Keep the Prog_enable pins unchanged for at least 10µs after the High-voltage has been
5. Wait until V
6. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
The loaded command and address are retained in the device during programming. For efficient
programming, the following should be considered.
• The command needs only be loaded once when writing or reading multiple memory locations
• Skip writing the data value 0xFF, that is the contents of the entire EEPROM (unless the
• Address high byte needs only be loaded before programming or reading a new 256 word
The Chip Erase will erase the Flash and EEPROM
not reset until the program memory has been completely erased. The Fuse bits are not
changed. A Chip Erase must be performed before the Flash and/or EEPROM are
reprogrammed.
Note:
Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give XTAL1 a positive pulse. This loads the command.
5. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low.
6. Wait until RDY/BSY goes high before loading a new command.
The Flash is organized in pages, see
the program data is latched into a page buffer. This allows one page of program data to be pro-
grammed simultaneously. The following procedure describes how to program the entire Flash
memory:
A. Load Command “Write Flash”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “0001 0000”. This is the command for Write Flash.
4. Give XTAL1 a positive pulse. This loads the command.
B. Load Address Low byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “0”. This selects low address.
3. Set DATA = Address low byte (0x00 - 0xFF).
EESAVE Fuse is programmed) and Flash after a Chip Erase
window in Flash or 256 byte EEPROM. This consideration also applies to Signature bytes
reading
applied to ensure the Prog_enable Signature has been latched.
commands.
1. The EEPRPOM memory is preserved during Chip Erase if the EESAVE Fuse is programmed.
CC
actually reaches 4.5V - 5.5V before giving any parallel programming
Table 28-9 on page
(1)
memories plus Lock bits. The Lock bits are
289. When programming the Flash,
ATmega48/88/168
292