ATmega168A Atmel Corporation, ATmega168A Datasheet - Page 70

no-image

ATmega168A

Manufacturer Part Number
ATmega168A
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega168A

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega168A-AU
Manufacturer:
ATMEL
Quantity:
464
Part Number:
ATmega168A-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega168A-AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-CCU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-CCUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega168A-PU
Manufacturer:
ATMEL
Quantity:
1 000
12.5
12.5.1
8271D–AVR–05/11
Register Description
Moving Interrupts Between Application and Boot Space, ATmega88A/88PA, ATmega168A/168PA and
ATmega328/328P
When the BOOTRST Fuse is programmed, the Boot section size set to 2Kbytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses in ATmega328/328P is:
The MCU Control Register controls the placement of the Interrupt Vector table.
MCUCR – MCU Control Register
Note:
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
Self-Programming” on page 280
tables, a special write procedure must be followed to change the IVSEL bit:
Bit
0x35 (0x55)
Read/Write
Initial Value
;
.org 0x3C00
0x3C00
0x3C01
0x3C02
0x3C03
0x3C04
0x3C05
Address Labels Code
;
.org 0x3C00
0x3C00
0x3C02
0x3C04
...
0x3C32
;
0x3C33
0x3C34
0x3C35
0x3C36
0x3C37
0x3C38
1. BODS and BODSE only available for picoPower devices ATmega48PA/88PA/168PA/328P
RESET: ldi
RESET: ldi
R
7
0
ATmega48A/PA/88A/PA/168A/PA/328/P
out
ldi
out
sei
<instr>
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
BODS
R/W
6
0
(1)
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
EXT_INT0
EXT_INT1
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
BODSE
xxx
xxx
for details. To avoid unintentional changes of Interrupt Vector
R/W
5
0
(1)
PUD
R/W
4
0
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
; Reset handler
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
”Boot Loader Support – Read-While-Write
R
3
0
R
2
0
IVSEL
R/W
1
0
IVCE
R/W
0
0
MCUCR
70

Related parts for ATmega168A