ATmega32 Atmel Corporation, ATmega32 Datasheet - Page 228
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega32
Manufacturer Part Number
ATmega32
Description
Manufacturer
Atmel Corporation
Specifications of ATmega32
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATmega32-16AC
Manufacturer:
COMPAL
Quantity:
500
Part Number:
ATmega32-16AU
Manufacturer:
ATMEL
Quantity:
20 000
Part Number:
ATmega32-16PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega32-16PU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
AVR_RESET; $C
BYPASS; $F
Boundary-scan
Related Register in I/O
Memory
MCU Control and
Status Register –
MCUCSR
2503Q–AVR–02/11
The active states are:
•
•
•
The AVR specific public JTAG instruction for forcing the AVR device into the Reset mode or
releasing the JTAG Reset source. The TAP controller is not reset by this instruction. The one bit
Reset Register is selected as Data Register. Note that the reset will be active as long as there is
a logic 'one' in the Reset Chain. The output from this chain is not latched.
The active states are:
•
Mandatory JTAG instruction selecting the Bypass Register for Data Register.
The active states are:
•
•
The MCU Control and Status Register contains control bits for general MCU functions, and pro-
vides information on which reset source caused an MCU Reset.
• Bit 7 – JTD: JTAG Interface Disable
When this bit is zero, the JTAG interface is enabled if the JTAGEN Fuse is programmed. If this
bit is one, the JTAG interface is disabled. In order to avoid unintentional disabling or enabling of
the JTAG interface, a timed sequence must be followed when changing this bit: The application
software must write this bit to the desired value twice within four cycles to change its value.
If the JTAG interface is left unconnected to other JTAG circuitry, the JTD bit should be set to
one. The reason for this is to avoid static current at the TDO pin in the JTAG interface.
• Bit 4 – JTRF: JTAG Reset Flag
This bit is set if a reset is being caused by a logic one in the JTAG Reset Register selected by
the JTAG instruction AVR_RESET. This bit is reset by a Power-on Reset, or by writing a logic
zero to the flag.
Bit
Read/Write
Initial Value
Capture-DR: Data on the external pins are sampled into the Boundary-scan Chain.
Shift-DR: The Boundary-scan Chain is shifted by the TCK input.
Update-DR: Data from the Boundary-scan Chain is applied to the output latches. However,
the output latches are not connected to the pins.
Shift-DR: The Reset Register is shifted by the TCK input.
Capture-DR: Loads a logic “0” into the Bypass Register.
Shift-DR: The Bypass Register cell between TDI and TDO is shifted.
JTD
R/W
7
0
ISC2
R/W
6
0
R
5
–
0
JTRF
R/W
4
WDRF
R/W
3
See Bit Description
BORF
R/W
2
EXTRF
R/W
1
ATmega32(L)
PORF
R/W
0
MCUCSR
228