ATmega32 Atmel Corporation, ATmega32 Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega32
Manufacturer Part Number
ATmega32
Description
Manufacturer
Atmel Corporation
Specifications of ATmega32
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATmega32-16AC
Manufacturer:
COMPAL
Quantity:
500
Part Number:
ATmega32-16AU
Manufacturer:
ATMEL
Quantity:
20 000
Part Number:
ATmega32-16PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega32-16PU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Calibrated Internal
RC Oscillator
2503Q–AVR–02/11
Table 7. External RC Oscillator Operating Modes
When this Oscillator is selected, start-up times are determined by the SUT fuses as shown in
Table
Table 8. Start-up Times for the External RC Oscillator Clock Selection
Note:
The Calibrated Internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0MHz clock. All frequen-
cies are nominal values at 5V and 25°C. This clock may be selected as the system clock by
programming the CKSEL fuses as shown in
components. The CKOPT Fuse should always be unprogrammed when using this clock option.
During Reset, hardware loads the calibration byte for the 1MHz into the OSCCAL Register and
thereby automatically calibrates the RC Oscillator. At 5V, 25°C and 1.0MHz Oscillator frequency
selected, this calibration gives a frequency within ±3% of the nominal frequency. Using calibra-
tion methods as described in application notes available at www.atmel.com/avr it is possible to
achieve ±1% accuracy at any given V
Chip Clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the reset
time-out. For more information on the pre-programmed calibration value, see the section
bration Byte” on page
Table 9. Internal Calibrated RC Oscillator Operating Modes
Note:
SUT1..0
00
01
10
11
8.
1. This option should not be used when operating close to the maximum frequency of the device.
1. The device is shipped with this option selected.
CKSEL3..0
Start-up Time from
Power-down and
0101
0110
0111
1000
Power-save
CKSEL3..0
6 CK
18 CK
18 CK
18 CK
0001
0010
0011
0100
258.
(1)
(1)
Additional Delay
(V
from Reset
CC
CC
4.1ms
4.1ms
65ms
and Temperature. When this Oscillator is used as the
= 5.0V)
–
Table
Frequency Range (MHz)
9. If selected, it will operate with no external
Nominal Frequency (MHz)
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
Fast rising power or BOD enabled
8.0 - 12.0
0.1 - 0.9
0.9 - 3.0
3.0 - 8.0
1.0
2.0
4.0
8.0
ATmega32(L)
“Cali-
29