ATmega32A Atmel Corporation, ATmega32A Datasheet - Page 262

• Manufacturer Part Number: ATmega32A
• Manufacturer: Atmel Corporation

Specifications of ATmega32A

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.8.11
25.8.12
8155C–AVR–02/11
Programming Time for Flash when using SPM
Simple Assembly Code Example for a Boot Loader
The Calibrated RC Oscillator is used to time Flash accesses.
gramming time for Flash accesses from the CPU.
Table 25-5.
Symbol
Flash write (Page Erase, Page Write,
and write Lock bits by SPM)
1. If there is no need for a Boot Loader update in the system, program the Boot Loader
2. Keep the AVR RESET active (low) during periods of insufficient power supply voltage.
3. Keep the AVR core in Power-down Sleep mode during periods of low V
.equ PAGESIZEB = PAGESIZE*2
.org SMALLBOOTSTART
Write_page:
Wrloop:
Lock bits to prevent any Boot Loader software updates.
This can be done by enabling the internal Brown-out Detector (BOD) if the operating
voltage matches the detection level. If not, an external low V
can be used. If a reset occurs while a write operation is in progress, the write operation
will be completed provided that the power supply voltage is sufficient.
vent the CPU from attempting to decode and execute instructions, effectively protecting
the SPMCR Register and thus the Flash from unintentional writes.
;-the routine writes one page of data from RAM to Flash
; the first data location in RAM is pointed to by the Y pointer
; the first data location in Flash is pointed to by the Z pointer
;-error handling is not included
;-the routine must be placed inside the boot space
; (at least the Do_spm sub routine). Only code inside NRWW section can
; be read during self-programming (page erase and page write).
;-registers used: r0, r1, temp1 (r16), temp2 (r17), looplo (r24),
; loophi (r25), spmcrval (r20)
; storing and restoring of registers is not included in the routine
; register usage can be optimized at the expense of code size
;-It is assumed that either the interrupt table is moved to the Boot
; loader section or that the interrupts are disabled.
; page erase
ldi
call Do_spm
; re-enable the RWW section
ldi
call Do_spm
; transfer data from RAM to Flash page buffer
ldi
ldi
ld
ld
ldi
call Do_spm
adiw ZH:ZL, 2
spmcrval, (1<<PGERS) | (1<<SPMEN)
spmcrval, (1<<RWWSRE) | (1<<SPMEN)
looplo, low(PAGESIZEB)
loophi, high(PAGESIZEB)
r0, Y+
r1, Y+
spmcrval, (1<<SPMEN)
SPM Programming Time.
Min Programming Time
; PAGESIZEB is page size in BYTES, not
; words
;init loop variable
;not required for PAGESIZEB<=256
3.7ms
Table 25-5
CC
Reset Protection circuit
Max Programming Time
ATmega32A
shows the typical pro-
CC
4.5ms
. This will pre-
262