ATmega32A Atmel Corporation, ATmega32A Datasheet - Page 42

• Manufacturer Part Number: ATmega32A
• Manufacturer: Atmel Corporation

Specifications of ATmega32A

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.4
10.5
10.5.1
8155C–AVR–02/11
Watchdog Timer
Register Description
MCUCSR – MCU Control and Status Register
ADC is used. To reduce power consumption in Power-down mode, the user can avoid the three
conditions above to ensure that the reference is turned off before entering Power-down mode.
The Watchdog Timer is clocked from a separate On-chip Oscillator which runs at 1MHz. This is
the typical value at V
controlling the Watchdog Timer prescaler, the Watchdog Reset interval can be adjusted as
shown in
dog Timer. The Watchdog Timer is also reset when it is disabled and when a Chip Reset occurs.
Eight different clock cycle periods can be selected to determine the reset period. If the reset
period expires without another Watchdog Reset, the ATmega32A resets and executes from the
Reset Vector. For timing details on the Watchdog Reset, refer to
To prevent unintentional disabling of the Watchdog, a special turn-off sequence must be fol-
lowed when the Watchdog is disabled. Refer to the description of the Watchdog Timer Control
Register for details.
Figure 10-7. Watchdog Timer
The MCU Control and Status Register provides information on which reset source caused an
MCU Reset.
• Bit 4 – JTRF: JTAG Reset Flag
This bit is set if a reset is being caused by a logic one in the JTAG Reset Register selected by
the JTAG instruction AVR_RESET. This bit is reset by a Power-on Reset, or by writing a logic
zero to the flag.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
Bit
Read/Write
Initial Value
Table 10-1 on page
JTD
R/W
7
0
CC
= 5V. See characterization data for typical values at other V
ISC2
R/W
6
0
OSCILLATOR
WATCHDOG
44. The WDR – Watchdog Reset – instruction resets the Watch-
R
5
–
0
JTRF
R/W
4
WDRF
R/W
3
See Bit Description
BORF
R/W
2
page
EXTRF
41.
R/W
1
ATmega32A
PORF
R/W
0
CC
levels. By
MCUCSR
42