ATmega644P Atmel Corporation, ATmega644P Datasheet - Page 153

• Manufacturer Part Number: ATmega644P
• Manufacturer: Atmel Corporation

Specifications of ATmega644P

• Flash (kbytes): 64 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8011O–AVR–07/10
When OC2A is connected to the pin, the function of the COM2A1:0 bits depends on the
WGM22:0 bit setting.
are set to a normal or CTC mode (non-PWM).
Table 14-2.
Table 14-3
mode.
Table 14-3.
Note:
Table 14-4
rect PWM mode.
Table 14-4.
Note:
• Bits 5:4 – COM2B1:0: Compare Match Output B Mode
These bits control the Output Compare pin (OC2B) behavior. If one or both of the COM2B1:0
bits are set, the OC2B output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC2B pin
must be set in order to enable the output driver.
COM2A1
COM2A1
COM2A1
0
0
1
1
0
0
1
1
0
0
1
1
1. A special case occurs when OCR2A equals TOP and COM2A1 is set. In this case, the Com-
1. A special case occurs when OCR2A equals TOP and COM2A1 is set. In this case, the Com-
pare Match is ignored, but the set or clear is done at BOTTOM. See
page 145
pare Match is ignored, but the set or clear is done at TOP. See
page 147
shows the COM2A1:0 bit functionality when the WGM21:0 bits are set to fast PWM
shows the COM2A1:0 bit functionality when the WGM22:0 bits are set to phase cor-
Compare Output Mode, non-PWM Mode
Compare Output Mode, Fast PWM Mode
Compare Output Mode, Phase Correct PWM Mode
COM2A0
COM2A0
COM2A0
for more details.
for more details.
0
1
0
1
0
1
0
1
0
1
0
1
Table 14-2
Description
Normal port operation, OC0A disconnected.
Toggle OC2A on Compare Match
Clear OC2A on Compare Match
Set OC2A on Compare Match
Description
Normal port operation, OC2A disconnected.
WGM22 = 0: Normal Port Operation, OC0A Disconnected.
WGM22 = 1: Toggle OC2A on Compare Match.
Clear OC2A on Compare Match, set OC2A at BOTTOM,
(non-inverting mode).
Set OC2A on Compare Match, clear OC2A at BOTTOM,
(inverting mode).
Description
Normal port operation, OC2A disconnected.
WGM22 = 0: Normal Port Operation, OC2A Disconnected.
WGM22 = 1: Toggle OC2A on Compare Match.
Clear OC2A on Compare Match when up-counting. Set OC2A on
Compare Match when down-counting.
Set OC2A on Compare Match when up-counting. Clear OC2A on
Compare Match when down-counting.
shows the COM2A1:0 bit functionality when the WGM22:0 bits
ATmega164P/324P/644P
(1)
(1)
”Phase Correct PWM Mode” on
”Fast PWM Mode” on
153