ATmega6490 Atmel Corporation, ATmega6490 Datasheet - Page 171
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega6490
Manufacturer Part Number
ATmega6490
Description
Manufacturer
Atmel Corporation
Specifications of ATmega6490
Flash (kbytes)
64 Kbytes
Pin Count
100
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
69
Ext Interrupts
32
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
160
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega6490-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega6490-16AU
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
ATmega6490-16AUR
Manufacturer:
Atmel
Quantity:
1 500
Company:
Part Number:
ATmega6490A-AU
Manufacturer:
Atmel
Quantity:
1 250
Company:
Part Number:
ATmega6490A-AUR
Manufacturer:
Maxim
Quantity:
43
Company:
Part Number:
ATmega6490P-AU
Manufacturer:
Atmel
Quantity:
779
19.3.2
19.3.3
2552K–AVR–04/11
Double Speed Operation (U2Xn)
External Clock
Table 19-1.
Note:
Some examples of UBRRn values for some system clock frequencies are found in
(see
The transfer rate can be doubled by setting the U2Xn bit in UCSRnA. Setting this bit only has
effect for the asynchronous operation. Set this bit to zero when using synchronous operation.
Setting this bit will reduce the divisor of the baud rate divider from 16 to 8, effectively doubling
the transfer rate for asynchronous communication. Note however that the Receiver will in this
case only use half the number of samples (reduced from 16 to 8) for data sampling and clock
recovery, and therefore a more accurate baud rate setting and system clock are required when
this mode is used. For the Transmitter, there are no downsides.
External clocking is used by the synchronous slave modes of operation. The description in this
section refers to
External clock input from the XCK pin is sampled by a synchronization register to minimize the
chance of meta-stability. The output from the synchronization register must then pass through
an edge detector before it can be used by the Transmitter and Receiver. This process intro-
duces a two CPU clock period delay and therefore the maximum external XCK clock frequency
is limited by the following equation:
Note that f
add some margin to avoid possible loss of data due to frequency variations.
Operating Mode
Asynchronous Normal
mode (U2Xn = 0)
Asynchronous Double
Speed mode
(U2Xn = 1)
Synchronous Master
mode
page
BAUD
f
UBRRn
OSC
1. The baud rate is defined to be the transfer rate in bit per second (bps)
osc
186).
depends on the stability of the system clock source. It is therefore recommended to
Equations for Calculating Baud Rate Register Setting
Figure 19-2
Baud rate (in bits per second, bps)
System Oscillator clock frequency
Contents of the UBRRnH and UBRRnL Registers, (0-4095)
BAUD
BAUD
BAUD
Equation for Calculating
for details.
Baud Rate
=
=
=
-------------------------------------- -
16 UBRR
---------------------------------- -
8 UBRR
---------------------------------- -
2 UBRR
(
(
(
f
f
f
f
XCK
OSC
OSC
OSC
(1)
ATmega329/3290/649/6490
<
+
+
+
f
---------- -
1
1
OSC
1
4
)
)
)
Equation for Calculating
UBRR
UBRR
UBRR
UBRRn Value
=
=
=
----------------------- - 1
16BAUD
------------------- - 1
8BAUD
------------------- - 1
2BAUD
f
f
f
OSC
OSC
OSC
–
–
–
Table 19-4
171