ATmega6490 Atmel Corporation, ATmega6490 Datasheet - Page 57

• Manufacturer Part Number: ATmega6490
• Manufacturer: Atmel Corporation

Specifications of ATmega6490

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.2.4
12.2.5
2552K–AVR–04/11
PCMSK3 – Pin Change Mask Register 3
PCMSK2 – Pin Change Mask Register 2
• Bit 4 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 – INTF0: External Interrupt Flag 0
When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set
(one). If the I-bit in SREG and the INT0 bit in EIMSK are set (one), the MCU will jump to the cor-
responding Interrupt Vector. The flag is cleared when the interrupt routine is executed.
Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared
when INT0 is configured as a level interrupt.
• Bit 6:0 – PCINT30..24: Pin Change Enable Mask 30..24
Each PCINT30..24-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT30..24 is set and the PCIE3 bit in EIMSK is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT30..24 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7:0 – PCINT23:16: Pin Change Enable Mask 23:16
Each PCINT23:16 bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT23:16 is set and the PCIE2 bit in EIMSK is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23:16 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
Note:
Bit
(0x6D)
Read/Write
Initial
Value
Bit
(0x73)
Read/Write
Initial Value
1. PCMSK3 and PCMSK2 are only present in ATmega3290/6490.
PCINT23
R/W
7
0
R
7
–
0
PCINT22
PCINT30
R/W
R/W
6
0
6
0
(1)
(1)
PCINT21
PCINT29
R/W
R/W
5
0
5
0
PCINT20
PCINT28
R/W
R/W
4
0
4
0
ATmega329/3290/649/6490
PCINT19
PCINT27
R/W
R/W
3
0
3
0
PCINT18
PCINT26
R/W
R/W
2
0
2
0
PCINT17
PCINT25
R/W
R/W
1
0
1
0
PCINT16
PCINT24
R/W
R/W
0
0
0
0
PCMSK2
PCMSK3
57