SAM7X512 Atmel Corporation, SAM7X512 Datasheet - Page 541

• Manufacturer Part Number: SAM7X512
• Manufacturer: Atmel Corporation

Specifications of SAM7X512

• Flash (kbytes): 512 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

SAM7X512/256/128
• BOFF: Bus Off Mode
0 = CAN controller is not in Bus Off Mode.
1 = CAN controller is in Bus Off Mode.
This flag is set depending on TEC counter value. A node is bus off when TEC counter is greater or equal to 256 (decimal).
This flag is automatically reset when above condition is not satisfied. Refer to
Section 36.6.4.6 “Error Interrupt Handler” on
page 515
for more information.
• SLEEP: CAN controller in Low power Mode
0 = CAN controller is not in low power mode.
1 = CAN controller is in low power mode.
This flag is automatically reset when Low power mode is disabled
• WAKEUP: CAN controller is not in Low power Mode
0 = CAN controller is in low power mode.
1 = CAN controller is not in low power mode.
When a WAKEUP event occurs, the CAN controller is synchronized with the bus activity. Messages can be transmitted or
received. The CAN controller clock must be available when a WAKEUP event occurs. This flag is automatically reset when
the CAN Controller enters Low Power mode.
• TOVF: Timer Overflow
0 = The timer has not rolled-over FFFFh to 0000h.
1 = The timer rolls-over FFFFh to 0000h.
This flag is automatically cleared by reading CAN_SR register.
• TSTP Timestamp
0 = No bus activity has been detected.
1 = A start of frame or an end of frame has been detected (according to the TEOF field in the CAN_MR register).
This flag is automatically cleared by reading the CAN_SR register.
• CERR: Mailbox CRC Error
0 = No CRC error occurred during a previous transfer.
1 = A CRC error occurred during a previous transfer.
A CRC error has been detected during last reception.
This flag is automatically cleared by reading CAN_SR register.
• SERR: Mailbox Stuffing Error
0 = No stuffing error occurred during a previous transfer.
1 = A stuffing error occurred during a previous transfer.
A form error results from the detection of more than five consecutive bit with the same polarity.
This flag is automatically cleared by reading CAN_SR register.
541
6120I–ATARM–06-Apr-11