SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 139
SAM9M10
Manufacturer Part Number
SAM9M10
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9M10.pdf
(59 pages)
4.SAM9M10.pdf
(1398 pages)
Specifications of SAM9M10
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
Yes
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 139 of 284
- Download datasheet (2Mb)
5.8.2
ARM DDI 0029G
Instructions
Communications through the DCC
The function of each register bit is as follows:
Bits 31:28
Bits 27:2
Bit 1
Bit 0
From the point of view of the debugger, the registers are accessed through scan chain 2
in the usual way. From the point of view of the processor, these registers are accessed
through coprocessor register transfer instructions.
Use the instructions listed in Table 5-1 to access the DCC registers.
Because the Thumb instruction set does not contain coprocessor instructions, you are
advised to access this data through SWI instructions when in Thumb state.
You can send and receive messages through the DCC. The following sections describe:
•
•
•
Sending a message to the debugger on page 5-18
Receiving a message from the debugger on page 5-18
Interrupt driven use of the DCC on page 5-18.
Copyright © 1994-2001. All rights reserved.
Explanation
Places the value from the DCC control register into the destination register (Rd)
Writes the value in the source register (Rn) to the DCC data write register
Returns the value in the DCC data read register into Rd
Contain a fixed pattern that denotes the EmbeddedICE version
number, in this case 0001.
Reserved.
If W is clear, the DCC data write register is ready to accept data
from the processor.
If W is set, there is data in the DCC data write register and the
debugger can scan it out.
If R is clear, the DCC data read register is free and data can be
placed there from the debugger.
If R is set, DCC data read register has data that has not been read
by the processor and the debugger must wait.
Table 5-1 DCC register access instructions
Debug Interface
5-17
Related parts for SAM9M10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: