DSPIC33FJ64MC508 Microchip Technology Inc., DSPIC33FJ64MC508 Datasheet - Page 34

• Manufacturer Part Number: DSPIC33FJ64MC508
• Description: High-performance, 16-bit Digital Signal Controllers
• Manufacturer: Microchip Technology Inc.

Visibility area (see Section 3.6.3 “Reading Data From
dsPIC33FJXXXMCX06/X08/X10 MOTOR CONTROL FAMILY
3.2
The dsPIC33FJXXXMCX06/X08/X10 Motor Control
Family CPU has a separate 16-bit wide data memory
space. The data space is accessed using separate
Address Generation Units (AGUs) for read and write
operations. Data memory maps of devices with differ-
ent RAM sizes are shown in Figure 3-3 through
Figure 3-5.
All Effective Addresses (EAs) in the data memory space
are 16 bits wide and point to bytes within the data space.
This arrangement gives a data space address range of
64 Kbytes or 32K words. The lower half of the data
memory space (that is, when EA<15> = 0) is used for
implemented memory addresses, while the upper half
(EA<15> = 1) is reserved for the Program Space
Program Memory Using Program Space Visibility”).
dsPIC33FJXXXMCX06/X08/X10 Motor Control Family
devices implement a total of up to 30 Kbytes of data
memory. Should an EA point to a location outside of
this area, an all-zero word or byte will be returned.
3.2.1
The data memory space is organized in byte
addressable, 16-bit wide blocks. Data is aligned in data
memory and registers as 16-bit words, but all data
space EAs resolve to bytes. The Least Significant
Bytes of each word have even addresses, while the
Most Significant Bytes have odd addresses.
3.2.2
To maintain backward compatibility with PIC
controllers and improve data space memory usage
efficiency, the dsPIC33FJXXXMCX06/X08/X10 Motor
Control Family instruction set supports both word and
byte operations. As a consequence of byte accessibil-
ity, all effective address calculations are internally
scaled to step through word-aligned memory. For
example, the core recognizes that Post-Modified
Register Indirect Addressing mode [Ws++] will result in
a value of Ws + 1 for byte operations and Ws + 2 for
word operations.
Data byte reads will read the complete word that
contains the byte, using the LSb of any EA to determine
which byte to select. The selected byte is placed onto
the LSb of the data path. That is, data memory and reg-
isters are organized as two parallel byte-wide entities
with shared (word) address decode but separate write
lines. Data byte writes only write to the corresponding
side of the array or register which matches the byte
address.
DS70287A-page 32
Data Address Space
DATA SPACE WIDTH
DATA MEMORY ORGANIZATION
AND ALIGNMENT
®
micro-
All word accesses must be aligned to an even address.
Misaligned word data fetches are not supported, so
care must be taken when mixing byte and word
operations or translating from 8-bit MCU code. If a
misaligned read or write is attempted, an address error
trap is generated. If the error occurred on a read, the
instruction underway is completed; if it occurred on a
write, the instruction will be executed but the write does
not occur. In either case, a trap is then executed,
allowing the system and/or user to examine the
machine state prior to execution of the address Fault.
All byte loads into any W register are loaded into the
Least Significant Byte. The Most Significant Byte is not
modified.
A sign-extend instruction (SE) is provided to allow
users to translate 8-bit signed data to 16-bit signed
values. Alternatively, for 16-bit unsigned data, users
can clear the MSb of any W register by executing a
zero-extend (ZE) instruction on the appropriate
address.
3.2.3
The first 2 Kbytes of the Near Data Space, from 0x0000
to 0x07FF, is primarily occupied by Special Function
Registers
dsPIC33FJXXXMCX06/X08/X10 Motor Control Family
core and peripheral modules for controlling the
operation of the device.
SFRs are distributed among the modules that they
control and are generally grouped together by module.
Much of the SFR space contains unused addresses;
these are read as ‘0’.
3.2.4
The 8-Kbyte area between 0x0000 and 0x1FFF is
referred to as the Near Data Space. Locations in this
space are directly addressable via a 13-bit absolute
address field within all memory direct instructions.
Additionally, the whole data space is addressable using
MOV instructions, which support Memory Direct
Addressing mode with a 16-bit address field, or by
using Indirect Addressing mode using a working
register as an Address Pointer.
Note:
SFR SPACE
The actual set of peripheral features and
interrupts varies by the device. Please
refer to the corresponding device tables
and pinout diagrams for device-specific
information.
NEAR DATA SPACE
(SFRs).
These
© 2007 Microchip Technology Inc.
are
used
by
the