MT9074AL Zarlink Semiconductor, Inc., MT9074AL Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
MT9074AL
Manufacturer Part Number
MT9074AL
Description
T1/E1/J1 Single Chip Transceiver
Manufacturer
Zarlink Semiconductor, Inc.
Datasheet
1.MT9074AL.pdf
(124 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT9074AL
Manufacturer:
ZARLINK
Quantity:
1 238
Company:
Part Number:
MT9074AL1
Manufacturer:
ZARLINK
Quantity:
22
Data Sheet
When the C4b and the E1.5o clocks are not phase-
locked, the rate at which data is being written into the
slip buffer from the DS1 side may differ from the rate
at which it is being read out onto the ST-BUS. If this
situation persists, the delay limits stated in the
previous paragraph will be violated and the slip
buffer will perform a controlled frame slip. That is, the
buffer pointers will be automatically adjusted so that
a full DS1 frame is either repeated or lost. All frame
slips occur on frame boundaries.
The minimum delay through the receive slip buffer is
approximately 1 usec and the maximum delay is
approximately 249 uS. Figure 13 illustrates the
relationship between the read and write pointers of
the
mapping). Measuring clockwise from the write
pointer, if the read page pointer comes within 8 usec
of the write page pointer a frame slip will occur,
which will put the read page pointer 157 usec from
the write page pointer. Conversely, if the read page
pointer moves more than 249 usec from the write
page pointer, a slip will occur, which will put the read
page pointer 124 usec from the write page pointer.
This provides a worst case hysteresis of 92 usec
peak = 142 U.I.
The RSLIP and RSLPD status bits (page 3H,
address 13H, bits 7 and 6 respectively) give
indication of a receive slip occurrence and direction.
Write Vectors
188 uS
Read Vectors
Minimum Delay
Read Vectors - Maximum Delay
Read Pointer
receive
Read Pointer
slip
157 uS
249 uS
512 Bit
Elastic
Store
buffer
Figure 13 - Read and write pointers in the receive slip buffers
Pointer
Read Pointer
Write
0 uS
Frame 0
32 uS
Frame 0
124 uS
(contiguous
Read Pointer
62 uS
XXX
Frame 1
time
Frame 1
slot
92 uS
92 uS
A maskable interrupt RxSLPI (page 1H, address
1BH, bit 0 - set high to mask) is also provided. RSLIP
changes state in the event of a slip. If RSLPD=0, the
slip buffer has overflowed and a frame was lost; if
RSLPD=1, an underflow condition occurred and a
frame was repeated
Slip Buffer in E1 Mode
In E1 mode, in addition to the elastic buffer in the
jitter attenuator(JA), another elastic buffer (two
frames deep) is present, attached between the
receive side and the ST-BUS (or GCI Bus) side of
the MT9074 in E1 mode. This elastic buffer is
configured as a slip buffer which absorbs wander
and low frequency jitter in multi-trunk applications.
The received PCM30 data is clocked into the slip
buffer with the E1.5o clock and is clocked out of the
slip buffer with the C4b clock. The E1.5o extracted
clock is generated from, and is therefore phase-
locked with, the receive PCM30 data. In normal
operation, the C4b clock will be phase-locked to the
E1.5o clock by a phase locked loop (PLL).
Therefore, in a single trunk system the receive data
is in phase with the E1.5o clock, the C4b clock is
phase-locked to the E1.5o clock, and the read and
write positions of the slip buffer will remain fixed with
respect to each other.
XXX
Frame 0
XXX
Wander Tolerance
Frame 1
MT9074
XXX
30