lan9303m Standard Microsystems Corp., lan9303m Datasheet - Page 50
lan9303m
Manufacturer Part Number
lan9303m
Description
Small Form Factor Three Port 10/100 Managed Ethernet Switch With Dual Mii/rmii/turbo Mii
Manufacturer
Standard Microsystems Corp.
Datasheet
1.LAN9303M.pdf
(380 pages)
- Current page: 50 of 380
- Download datasheet (5Mb)
Revision 1.3 (08-27-09)
4.2.2
4.2.2.1
4.2.3
4.2.3.1
A nRST pin reset typically takes approximately 760uS, plus an additional 91uS per byte of data loaded
from the EEPROM via the EEPROM Loader. A full EEPROM load of 64KB will complete in
approximately 6.0 seconds.
Note: The nRST pin is pulled-high internally. If unused, this signal can be left unconnected. Do not
Please refer to
Multi-Module Resets
Multi-module resets activate multiple internal resets, but do not reset the entire chip. Configuration
straps are not latched upon multi-module resets. A multi-module reset is initiated by assertion of the
following:
Multi-module reset/configuration completion can be determined by first polling the
Register
Once the returned data is the correct byte ordering value, the serial interface resets have completed.
The completion of the entire chip-level reset must then be determined by polling the
(READY)
Ready (READY)
With the exception of the
(BYTE_TEST), and
forbidden while the
Device Ready (READY)
Note: The digital reset does not reset register bits designated as NASR.
Digital Reset (DIGITAL_RST)
A digital reset is performed by setting the
Register
PHY, Port 2 PHY, and Virtual PHY). The EEPROM Loader will automatically run following this reset.
Configuration straps are not latched as a result of a digital reset.
A digital reset typically takes approximately 760uS, plus an additional 91uS per byte of data loaded
from the EEPROM via the EEPROM Loader. A full EEPROM load of 64KB will complete in
approximately 6.0 seconds.
Single-Module Resets
A single-module reset will reset only the specified module. Single-module resets do not latch the
configuration straps or initiate the EEPROM Loader. A single-module reset is initiated by assertion of
the following:
Port 2 PHY Reset
A Port 2 PHY reset is performed by setting the
Register (RESET_CTL)
(PHY_BASIC_CONTROL_x). Upon completion of the Port 2 PHY reset, the
(PHY2_RST)
are affected by this reset.
Digital Reset (DIGITAL_RST)
Port 2 PHY Reset
Port 1 PHY Reset
Virtual PHY Reset
rely on internal pull-up resistors to drive signals external to the device.
(BYTE_TEST). The returned data will be invalid until the serial interface resets are complete.
(RESET_CTL). A digital reset will reset all sub-modules except the Ethernet PHYs (Port 1
bit of the
and
Section Table 3.8, "Miscellaneous Pins," on page 44
bit indicates that the reset has completed and the device is ready to be accessed.
Reset (PHY_RST)
Hardware Configuration Register (HW_CFG)
Device Ready (READY)
Reset Control Register
or the
bit is set.
Hardware Configuration Register
Small Form Factor Three Port 10/100 Managed Ethernet Switch with Dual MII/RMII/Turbo MII
Reset (PHY_RST)
DATASHEET
bits are automatically cleared. No other modules of the device
50
(RESET_CTL), read access to any internal resources is
bit is cleared. Writes to any address are invalid until the
Digital Reset (DIGITAL_RST)
Port 2 PHY Reset (PHY2_RST)
bit in the (x=2)
(HW_CFG),
until it is set. When set, the
Port x PHY Basic Control Register
for a description of the nRST pin.
SMSC LAN9303M/LAN9303Mi
Byte Order Test Register
bit of the
bit of the
Port 2 PHY Reset
Byte Order Test
Reset Control
Device Ready
Reset Control
Datasheet
Device
Related parts for lan9303m
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: