hd64338023s Renesas Electronics Corporation., hd64338023s Datasheet - Page 340
hd64338023s
Manufacturer Part Number
hd64338023s
Description
Renesas 8-bit Single-chip Microcomputer Super Low Power Series
Manufacturer
Renesas Electronics Corporation.
Datasheet
1.HD64338023S.pdf
(697 pages)
- Current page: 340 of 697
- Download datasheet (6Mb)
Section 9 Timers
When the pin function is switched and an edge is generated in the input capture input signal, if this
edge matches the edge selected by the input capture interrupt select (IIEGS) bit, the interrupt
request flag will be set to 1. The interrupt request flag should therefore be cleared to 0 before use.
Figure 9.15 shows the procedure for port mode register manipulation and interrupt request flag
clearing. When switching the pin function, set the interrupt-disabled state before manipulating the
port mode register, then, after the port mode register operation has been performed, wait for the
time required to confirm the input capture input signal as an input capture signal (at least two
system clocks when the noise canceler is not used; at least five sampling clocks when the noise
canceler is used), before clearing the interrupt enable flag to 0. There are two ways of preventing
interrupt request flag setting when the pin function is switched: by controlling the pin level so that
the conditions shown in tables 9.14 and 9.15 are not satisfied, or by setting the opposite of the
generated edge in the IIEGS bit in TMG.
Rev. 7.00 Mar 10, 2005 page 298 of 652
REJ09B0042-0700
Figure 9.15 Port Mode Register Manipulation and Interrupt Enable Flag Clearing
Clear interrupt request flag to 0
Manipulate port mode register
* TMIG confirmation time
Clear I bit in CCR to 0
Set I bit in CCR to 1
Disable interrupts. (Interrupts can also be disabled by
manipulating the interrupt enable bit in interrupt enable
register 2.)
After manipulating the port mode register, wait for the
TMIG confirmation time * (at least two system clocks when
the noise canceler is not used; at least five sampling
clocks when the noise canceler is used), then clear the
interrupt enable flag to 0.
Enable interrupts
Procedure
Related parts for hd64338023s
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
(HD64 Series) Hitachi Single-Chip Microcomputer
Manufacturer:
Hitachi Semiconductor
Datasheet:
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
RENESAS MCU M16C FAMILY / M16C/Tiny SERIES
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Starter Kit for RX210
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas StarterKit for RX630
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit+ for RX63N
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
FLASH PROGRAMMER FOR RENESAS MICROCONTROLLERS
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet: