PIC18F2480 MICROCHIP [Microchip Technology], PIC18F2480 Datasheet - Page 290

no-image

PIC18F2480

Manufacturer Part Number
PIC18F2480
Description
28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F2480-E/ML
Manufacturer:
MICROCHIP
Quantity:
1 001
Part Number:
PIC18F2480-E/SO
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
PIC18F2480-I/SO
Manufacturer:
Microchi
Quantity:
9 999
Part Number:
PIC18F2480-I/SO
Manufacturer:
MIC
Quantity:
20 000
Part Number:
PIC18F2480-I/SO
0
Part Number:
PIC18F2480-I/SP
Manufacturer:
TDK
Quantity:
64
Part Number:
PIC18F2480-I/SP
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC18F2480/2580/4480/4580
REGISTER 23-13: RXB0CON: RECEIVE BUFFER 0 CONTROL REGISTER (CONTINUED)
DS39637A-page 288
bit 2
bit 1
bit 0
Legend:
C = Clearable bit
-n = Value at POR
Mode 0:
RXB0DBEN: Receive Buffer 0 Double-Buffer Enable bit
1 = Receive Buffer 0 overflow will write to Receive Buffer 1
0 = No Receive Buffer 0 overflow to Receive Buffer 1
Mode 1, 2:
FILHIT2: Filter Hit bit 2
This bit combines with other bits to form filter acceptance bits <4:0>.
Mode 0:
JTOFF: Jump Table Offset bit (read-only copy of RXB0DBEN)
1 = Allows jump table offset between 6 and 7
0 = Allows jump table offset between 1 and 0
Mode 1, 2:
FILHIT1: Filter Hit bit 1
This bit combines with other bits to form filter acceptance bits <4:0>.
Mode 0:
FILHIT0: Filter Hit bit 0
This bit indicates which acceptance filter enabled the message reception into Receive Buffer 0.
1 = Acceptance Filter 1 (RXF1)
0 = Acceptance Filter 0 (RXF0)
Mode 1, 2:
FILHIT0: Filter Hit bit 0
This bit, in combination with FILHIT<4:1>, indicates which acceptance filter enabled the message
reception into this receive buffer.
01111 = Acceptance Filter 15 (RXF15)
01110 = Acceptance Filter 14 (RXF14)
...
00000 = Acceptance Filter 0 (RXF0)
Note 1: This bit is set by the CAN module upon receiving a message and must be cleared by
2: This bit allows same filter jump table for both RXB0CON and RXB1CON.
software after the buffer is read. As long as RXFUL is set, no new message will be
loaded and buffer will be considered full. After clearing the RXFUL flag, the PIR3 bit,
RXB0IF, can be cleared. If RXB0IF is cleared, but RXFUL is not cleared, then RXB0IF
is set again.
R = Readable bit
‘1’ = Bit is set
Preliminary
W = Writable bit
‘0’ = Bit is cleared
(2)
U = Unimplemented bit, read as ‘0’
x = Bit is unknown
 2004 Microchip Technology Inc.

Related parts for PIC18F2480