AM79C971KCW AMD [Advanced Micro Devices], AM79C971KCW Datasheet - Page 72
![no-image](/images/no-image-200.jpg)
AM79C971KCW
Manufacturer Part Number
AM79C971KCW
Description
Manufacturer
AMD [Advanced Micro Devices]
Datasheet
1.AM79C971KCW.pdf
(265 pages)
- Current page: 72 of 265
- Download datasheet (3Mb)
The time delay from the last rising edge of the message
to IRXEN deassert allows the last bit to be strobed by
IRXCLK and transferred to the controller section, but
prevents any extra bit(s) at the end of message.
Data Decoding
The data receiver is a comparator with clocked output
to minimize noise sensitivity to the DI inputs. Input
error is less than 35 mV to minimize sensitivity to input
rise and fall time. IRXCLK strobes the data receiver
output at 1/4 bit time to determine the value of the
Manchester bit, and clocks the data out on IRXDAT on
the following IRXCLK. The data receiver also gener-
ates the signal used for phase detector comparison to
the internal MENDEC VCO.
Jitter Tolerance Definition
The MENDEC utilizes a clock capture circuit to align its
internal data strobe with an incoming bit stream. The
clock acquisition circuitry requires four valid bits with
the values 1010b. The clock is phase-locked to the neg-
ative transition at the bit cell center of the second zero
in the pattern.
Since data is strobed at 1/4 bit time, Manchester tran-
sitions which shift from their nominal placement
through 1/4 bit time will result in improperly decoded
data. With this as the criterion for an error, a definition
of Jitter Handling is:
Attachment Unit Interface
The Attachment Unit Interface (AUI) is the PLS (Physi-
cal Layer Signaling) to PMA (Physical Medium Attach-
ment) interface which effectively connects the DTE to a
MAU. The differential interface provided by the
Am79C971 controller is fully compliant to Section 7 of
ISO 8802-3 (ANSI/IEEE 802.3) standard.
After the Am79C971 controller initiates a transmission
it will expect to see data “looped-back” on the DI pair
(when the AUI port is selected). This will internally gen-
erate a “carrier sense,” indicating that the integrity of
the data path to and from the MAU is intact, and that the
MAU is operating correctly. This “carrier sense” signal
must be asserted before end of transmission. If “carrier
sense” does not become active in response to the data
transmission, or becomes inactive before the end of
transmission, the loss of carrier (LCAR) error bit will be
set in the transmit descriptor ring (TMD2, bit 27) after
the frame has been transmitted.
Differential Input Termination
The differential input for the Manchester data (DI ) is
externally terminated by two 40.2-
optional common-mode bypass capacitor, as shown in
Figure 36. The differential input impedance, Z
72
cell position from nominal input transition, for which
the MENDEC section will properly decode data.
The peak deviation approaching or crossing 1/4 bit
resistors and one
IDF
, and
Am79C971
the common-mode input impedance, Z
fied so that the Ethernet specification for cable termina-
tion impedance is met using standard 1% resistor
terminators. If SIP devices are used, 39 ohms is also a
suitable value. The CI differential inputs are termi-
nated in exactly the same way as the DI pair.
Collision Detection
A MAU detects the collision condition on the network
and generates a 10-MHz differential signal at the CI
inputs. This collision signal passes through an input
stage which detects signal levels and pulse duration.
When the signal is detected by the MENDEC, it sets the
ICLSN line HIGH. The condition continues for approxi-
mately 1.5 bit times after the last LOW-to-HIGH transi-
tion on CI .
Twisted-Pair Transceiver
This section describes operation of the Twisted-Pair
Transceiver (T-MAU) when operating in half-duplex
mode. When in half-duplex mode, the T-MAU imple-
ments the MAU functions for the Twisted Pair Medium
as specified by the supplement to the IEEE 802.3 stan-
dard (Type 10BASE-T). When operating in full-duplex
mode, the MAC engine behavior changes as described
in the section Full-Duplex Operation.
The T-MAU provides twisted pair driver and receiver cir-
cuits, including on-board transmit digital predistortion
and receiver squelch, and a number of additional fea-
tures including Link Status indication, Automatic
Twisted Pair Receive Polarity Detection/Correction and
Indication, Receive Carrier Sense, Transmit Active, and
Collision Present indication.
Twisted Pair Transmit Function
The differential driver circuitry in the TXD and TXP
pins provides the necessary electrical driving capability
and the pre-distortion control for transmitting signals
over maximum length Twisted Pair cable, as specified
by the 10BASE-T supplement to the ISO 8802-3 (IEEE/
Figure 36. AUI Differential Input Termination
Am79C971
DI+
DI-
40.2
0.01 F
0.1 F
to
40.2
AUI Isolation
Transformer
ICM
, are speci-
20550D-39
Related parts for AM79C971KCW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AMD-751AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751ACAMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-751](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751AMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-X5-133SFZ](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-X5-133SFZAm5X86? Microprocessor Family
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8131BLC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Hyper Transport PCI-X Tunnel
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8111AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
HyperTransport I/O Hub
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-640AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
System Controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-K6](/images/no-image3.png)
Part Number:
Description:
AMD-K6 Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-K6-2E/400AFR](/images/no-image3.png)
Part Number:
Description:
AMD-K6-2E Embedded Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-8132BLCT](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-K6-IIIE+550ACR](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-766AC](/images/no-image3.png)
Part Number:
Description:
Peripheral Bus Controller
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet: