C8051F989-GUR Silicon Labs, C8051F989-GUR Datasheet - Page 87
C8051F989-GUR
Manufacturer Part Number
C8051F989-GUR
Description
8-bit Microcontrollers - MCU 4kB 512B RAM
Manufacturer
Silicon Labs
Datasheet
1.C8051F986-GUR.pdf
(322 pages)
Specifications of C8051F989-GUR
Rohs
yes
Core
8051
Data Bus Width
8 bit
Processor Series
C8051
- Current page: 87 of 322
- Download datasheet (2Mb)
C8051F99x-C8051F98x
5.10. External Voltage Reference
To use an external voltage reference, REFSL[1:0] should be set to 00. Bypass capacitors should be added
as recommended by the manufacturer of the external voltage reference. If the manufacturer does not pro-
vide recommendations, a 4.7uF in parallel with a 0.1uF capacitor is recommended.
5.11. Internal Voltage Reference
For applications requiring the maximum number of port I/O pins, or very short VREF turn-on time, the
1.65 V high-speed reference will be the best internal reference option to choose. The high speed internal
reference is selected by setting REFSL[1:0] to 11. When selected, the high speed internal reference will be
automatically enabled/disabled on an as-needed basis by ADC0.
For applications with a non-varying power supply voltage, using the power supply as the voltage reference
can provide ADC0 with added dynamic range at the cost of reduced power supply noise rejection. To use
the 1.8 to 3.6 V power supply voltage (V
) or the 1.8 V regulated digital supply voltage as the reference
DD
source, REFSL[1:0] should be set to 01 or 10, respectively.
5.12. Analog Ground Reference
To prevent ground noise generated by switching digital logic from affecting sensitive analog
measurements, a separate analog ground reference option is available. When enabled, the ground
reference for ADC0 during both the tracking/sampling and the conversion periods is taken from the
P0.1/AGND pin. Any external sensors sampled by ADC0 should be referenced to the P0.1/AGND pin. This
pin should be connected to the ground terminal of any external sensors sampled by ADC0. If an external
voltage reference is used, the P0.1/AGND pin should be connected to the ground of the external reference
and its associated decoupling capacitor. The separate analog ground reference option is enabled by
setting REFGND to 1. Note that when sampling the internal temperature sensor, the internal chip ground is
always used for the sampling operation, regardless of the setting of the REFGND bit. Similarly, whenever
the internal 1.65 V high-speed reference is selected, the internal chip ground is always used during the
conversion period, regardless of the setting of the REFGND bit.
5.13. Temperature Sensor Enable
The TEMPE bit in register REF0CN enables/disables the temperature sensor. While disabled, the
temperature sensor defaults to a high impedance state and any ADC0 measurements performed on the
sensor result in meaningless data. See Section “5.8. Temperature Sensor” on page 83 for details on
temperature sensor characteristics when it is enabled.
Rev. 1.1
87
Related parts for C8051F989-GUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: