AT26F004-MU Atmel, AT26F004-MU Datasheet - Page 2
![IC FLASH 4MBIT 33MHZ 8QFN](/photos/7/26/72647/8-vfqfn-8m1-a_sml.jpg)
AT26F004-MU
Manufacturer Part Number
AT26F004-MU
Description
IC FLASH 4MBIT 33MHZ 8QFN
Manufacturer
Atmel
Datasheet
1.AT26F004-MU.pdf
(38 pages)
Specifications of AT26F004-MU
Format - Memory
FLASH
Memory Type
DataFLASH
Memory Size
4M (2048 pages x 256 bytes)
Speed
33MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-VFQFN, 8-VFQFPN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT26F004-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
2. Pin Descriptions and Pinouts
Table 2-1.
2
Symbol
HOLD
GND
SCK
WP
V
CS
SO
SI
CC
AT26F004
Name and Function
CHIP SELECT: Asserting the CS pin selects the device. When the CS pin is deasserted, the
device will be deselected and normally placed in standby mode (not Deep Power-down mode), and
the SO pin will be in a high-impedance state. When the device is deselected, data will not be
accepted on the SI pin.
A high-to-low transition on the CS pin is required to start an operation, and a low-to-high transition
is required to end an operation. When ending an internally self-timed operation such as a program
or erase cycle, the device will not enter the standby mode until the completion of the operation.
SERIAL CLOCK: This pin is used to provide a clock to the device and is used to control the flow of
data to and from the device. Command, address, and input data present on the SI pin is always
latched on the rising edge of SCK, while output data on the SO pin is always clocked out on the
falling edge of SCK.
SERIAL INPUT: The SI pin is used to shift data into the device. The SI pin is used for all data input
including command and address sequences. Data on the SI pin is always latched on the rising
edge of SCK.
SERIAL OUTPUT: The SO pin is used to shift data out from the device. Data on the SO pin is
always clocked out on the falling edge of SCK.
WRITE PROTECT: The WP pin controls the hardware locking feature of the device. Refer to
section
and the WP pin.
The WP pin is not internally pulled-high and cannot be left floating. If hardware controlled locking
will not be used, then the WP pin must be externally connected to V
HOLD: The HOLD pin is used to temporarily pause serial communication without deselecting
or resetting the device. While the HOLD pin is asserted, transitions on the SCK pin and data on the
SI pin will be ignored, and the SO pin will be in a high-impedance state.
The CS pin must be asserted, and the SCK pin must be in the low state in order for a Hold
condition to start. A Hold condition pauses serial communication only and does not have an effect
on internally self-timed operations such as a program or erase cycle. Please refer to section
on page 27
The HOLD pin is not internally pulled-high and cannot be left floating. If the Hold function will not
be used, then the HOLD pin must be externally connected to V
DEVICE POWER SUPPLY: The V
Operations at invalid V
GROUND: The ground reference for the power supply. GND should be connected to the
system ground.
Pin Descriptions
“Protection Commands and Features” on page 13
for additional details on the Hold operation.
The AT26F004 also offers a sophisticated method for protecting individual sectors against
erroneous or malicious program and erase operations. By providing the ability to individually
protect and unprotect sectors, a system can unprotect a specific sector to modify its contents
while keeping the remaining sectors of the memory array securely protected. This is useful in
applications where program code is patched or updated on a subroutine or module basis, or in
applications where data storage segments need to be modified without running the risk of errant
modifications to the program code segments.
Specifically designed for use in 3-volt systems, the AT26F004 supports read, program, and
erase operations with a supply voltage range of 2.7V to 3.6V. No separate voltage is required for
programming and erasing.
CC
voltages may produce spurious results and should not be attempted.
CC
pin is used to supply the source voltage to the device.
for more details on protection features
CC
.
CC
.
“Hold”
Asserted
State
Low
Low
Low
3588D–DFLASH–10/08
–
–
–
–
–
Output
Power
Power
Type
Input
Input
Input
Input
Input