C8051F045R Silicon Labs, C8051F045R Datasheet - Page 269

• Manufacturer Part Number: C8051F045R
• Description: 8-bit Microcontrollers - MCU 25 MIPS 64KB 10ADC
• Manufacturer: Silicon Labs

Specifications of C8051F045R

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 4.25 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: TQFP-64
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 13
• Data Rom Size: 64 KB
• Interface Type: CAN, SMBus, SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Processor Series: C8051
• Program Memory Type: Flash
• Factory Pack Quantity: 500
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V

21.1.3. Mode 2: 9-Bit UART, Fixed Baud Rate
Mode 2 provides asynchronous, full-duplex communication using a total of eleven bits per data byte: a start
bit, 8 data bits (LSB first), a programmable ninth data bit, and a stop bit. Mode 2 supports multiprocessor
communications and hardware address recognition (see
determined by the value in TB80 (SCON0.3). It can be assigned the value of the parity flag P in the PSW or
used in multiprocessor communications. On receive, the ninth data bit goes into RB80 (SCON0.2) and the
stop bit is ignored.
Data transmission begins when an instruction writes a data byte to the SBUF0 register. The TI0 Transmit
Interrupt Flag (SCON0.1) is set at the end of the transmission (the beginning of the stop-bit time). Data
reception can begin any time after the REN0 Receive Enable bit (SCON0.4) is set to logic 1. After the stop
bit is received, the data byte will be loaded into the SBUF0 receive register if RI0 is logic 0 and one of the
following requirements are met:
•
•
If the above conditions are satisfied, the eight bits of data are stored in SBUF0, the ninth bit is stored in
RB80 and the RI0 flag is set. If these conditions are not met, SBUF0 and RB80 will not be loaded and the
RI0 flag will not be set. An interrupt will occur if enabled when either TI0 or RI0 are set.
The baud rate in Mode 2 is either SYSCLK / 32 or SYSCLK / 64, according to the value of the SMOD0 bit
in register SSTA0.
SPACE
MARK
SM20 is logic 0
SM20 is logic 1, the received 9th bit is logic 1, and the received address matches the UART0 address
as described in
BIT TIMES
BIT SAMPLING
START
Figure 21.6. UART0 Modes 1, 2, and 3 Interconnect Diagram
BIT
Section
Figure 21.5. UART0 Modes 2 and 3 Timing Diagram
D0
21.2.
Equation 21.5. Mode 2 Baud Rate
D1
BaudRate
RS-232
MCU
D2
TX
RX
=
D3
2
Rev. 1.5
RS-232
LEVEL
SMOD0
XLTR
OR
C8051F040/1/2/3/4/5/6/7
D4
Section

RX
RX
TX
TX
C8051Fxxx


SYSCLK
--------------------- -
C8051Fxxx
D5
64
21.2). On transmit, the ninth data bit is


D6
D7
D8
STOP
BIT
269