LDS8141-002-T2 IXYS, LDS8141-002-T2 Datasheet - Page 10

• Manufacturer Part Number: LDS8141-002-T2
• Description: IC LED DRIVER WHIT BCKLGT 16WQFN
• Manufacturer: IXYS
• Series: LED-Sense™, Power-Lite™r
• Type: Backlight, White LED (I²C Interface)r

Specifications of LDS8141-002-T2

• Topology: High Side, Linear (LDO), PWM
• Number Of Outputs: 4
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 1.2MHz
• Voltage - Supply: 2.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-WQFN, 16-miniQFN
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 32mA
• Internal Switch(s): Yes
• Efficiency: 80%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Details
• Other names: LDS8141-002-T2-2

LDS8161/41
PIN DESCRIPTION
PIN FUNCTION
V
capacitor is required between the V
near the device. The operating input voltage range is
from 2.5 V to 5.5 V.
EN is the enable input for the entire device.
Guaranteed levels of logic high and logic low are set
at 1.3 V and 0.4V respectively. When EN is initially
taken high, the device becomes enabled and may
communicate through I
SDAT is the I
line allowing data to be written into and read from the
four registers in the driver..
SCLK is the I
SADD is I
GND or VIN pin to allow choice of two salve
addresses
© 2009 IXYS Corp.
Characteristics subject to change without notice
I
I
I
Ground Reference
Device enable (active high)
LEDC2 anode terminal -8161 (NC for 8141)
LEDC1 anode terminal -8161 (NC for 8141)
LEDB2 anode terminal
LEDB1 anode terminal
LEDA2 anode terminal
LEDA1 anode terminal
Power Source Input; connect to battery or supply
Test pin
Not connect (no internal connect to the device)
Connect to GND on the PCB
IN
2
2
2
C Serial clock input
C Serial data input/output
C Serial interface Address Programming
is the supply pin. A small 1
2
C Serial interface Addresses tie to either
2
2
C serial clock input.
C serial data line. This is a bidirectional
Function
2
C interface
μ
F ceramic bypass
IN
pin and ground
LEDC2
LEDC1
LEDB2
LEDB1
LEDA2
LEDA1
Name
SADD
SCLK
SDAT
GND
PAD
TST
Pin
EN
V
NC
10
IN
GND is the ground reference for internal circuitry.
The pin must be connected to the ground plane on
the PCB.
LEDA1 – LEDC2 provide the internal regulated
current source for each of the LED anodes. These
pins
whenever the device is in shutdown mode. LEDC1
and LEDC2 are no connects (NC) for the LDS8141.
PAD is the exposed pad underneath the package.
For best thermal performance, the tab should be
soldered to the PCB and connected to the ground
plane
TST is a test pin used by factory only. Leave it
floating (no external connection)
5, 7, 16
PAD
8161
10
11
12
13
14
15
1
2
3
4
6
8
9
enter
Pin #
5, 7, 8,
9, 16
PAD
8141
high-impedance
10
11
12
13
14
15
1
2
3
4
6
Doc. No. 8141/61_DS, Rev. N1.0
zero
current
state