XE8000EV101 Semtech, XE8000EV101 Datasheet - Page 120
XE8000EV101
Manufacturer Part Number
XE8000EV101
Description
EVAL BOARD FOR XE8801AMI027LF
Manufacturer
Semtech
Type
MCUr
Specifications of XE8000EV101
Contents
Fully Assembled Evaluation Board
For Use With/related Products
XE88LC01AMI027
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 120 of 135
- Download datasheet (2Mb)
CounterA and CounterB are 8-bit counters and can be combined to form a 16-bit counter. CounterC and CounterD
exhibit the same features.
The counters can also be used to generate two PWM outputs on PB[0] and PB[1]. In PWM mode one can generate
PWM functions with 8, 10, 12, 14 or 16 bit wide counters.
The counters A and B can be captured by events on an internal or an external signal. The capture can be
performed on both 8-bit counters running individually on two different clock sources or on both counters chained to
form a 16-bit counter. In any case, the same capture signal is used for both counters.
When the counters A and B are not chained, they can be used in several configurations: A and B as counters, A
and B as captured counters, A as PWM and B as counter, A as PWM and B as captured counter.
When the counters C and D are not chained, they can be used either both as counters or counter C as PWM and
counter D as counter.
Note: When writing to RegCntA or RegCntB, the processor writes the counter comparison values. When reading
these locations, the processor reads back either the actual counter value or the last captured value if the capture
mode is active.
© Semtech 2005
18.1 Features
18.2 Overview
18.3 Register map
•
•
•
•
•
•
•
•
•
•
4 x 8-bits timer/counter modules or 2 x 16-bits timers/counter modules
Each with 4 possible clock sources
Up/down counter modes
Interrupt and event generation
Capture function (internal or external source)
Rising, falling or both edge of capture signal
PA[3:0] can be used as clock inputs (debounced or direct)
2 x 8 bits PWM or 2 x 16 bits PWM
PWM resolution of 8, 10, 12, 14 or 16 bits
Complex mode combinations are possible between counter, capture and PWM modes
7-0
7-0
7-0
7-0
7-0
7-0
Bit
bit
bit
CounterA
CounterA
CounterB
CounterB
CounterC
CounterC
RegCntA
RegCntB
RegCntC
rw
rw
rw
w
w
w
r
r
r
Table 18-1. RegCntA
Table 18-2. RegCntB
Table 18-3. RegCntC
18-2
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
reset
reset
reset
8-bits comparison value
8-bits comparison value
8-bits comparison value
XE8801A – SX8801R
8-bits counter value
8-bits counter value
8-bits counter value
function
function
function
www.semtech.com
Related parts for XE8000EV101
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: