PIC18F1320-I/SO Microchip Technology, PIC18F1320-I/SO Datasheet - Page 162

• Manufacturer Part Number: PIC18F1320-I/SO
• Description: IC MCU FLASH 4KX16 A/D 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1320-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 18-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA12XP080 - ADAPTER DEVICE FOR MPLAB-ICEAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F1220/1320
17.1
For the A/D converter to meet its specified accuracy,
the charge holding capacitor (C
to fully charge to the input channel voltage level. The
analog input model is shown in Figure 17-2. The
source impedance (R
switch (R
required to charge the capacitor C
switch (R
(V
at the analog input (due to pin leakage current). The
maximum recommended impedance for analog
sources is 2.5 k . After the analog input channel is
selected (changed), the channel must be sampled for
at least the minimum acquisition time before starting a
conversion.
To
Equation 17-1 may be used. This equation assumes
that 1/2 LSb error is used (1024 steps for the A/D). The
1/2 LSb error is the maximum error allowed for the A/D
to meet its specified resolution.
EQUATION 17-1:
EQUATION 17-2:
EXAMPLE 17-1:
DS39605C-page 160
T
V
or
T
T
T
T
Temperature coefficient is only required for temperatures > 25ºC. Below 25ºC, T
T
T
ACQ
C
ACQ
AMP
COFF
C
ACQ
DD
Note:
HOLD
). The source impedance affects the offset voltage
calculate
= Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient
= T
= T
= 5 s
= (Temp – 25ºC)(0.05 s/ºC)
= -(C
= 5 s + 1.25 s + 9.61 s
=
=
A/D Acquisition Requirements
SS
(50ºC – 25ºC)(0.05 s/ºC)
1.25 s
-(120 pF) (1 k + 7 k + 2.5 k ) ln(0.0004883) s
9.61 s
12.86 s
SS
AMP
( V
-(C
AMP
) impedance varies over the device voltage
When the conversion is started, the
holding capacitor is disconnected from the
input pin.
HOLD
) impedance directly affect the time
HOLD
REF
+ T
+ T
)(R
the
C
– ( V
C
)(R
+ T
+ T
IC
IC
COFF
+ R
COFF
ACQUISITION TIME
A/D MINIMUM CHARGING TIME
REF
CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME
+ R
S
minimum
) and the internal sampling
SS
/2048)) • (1 – e
SS
+ R
+ R
S
) ln(1/2047) s
S
HOLD
) ln(1/2048)
HOLD
acquisition
) must be allowed
(-T
. The sampling
C
/C
HOLD
(R
IC
+ R
time,
SS
+ R
S
))
)
Example 17-1 shows the calculation of the minimum
required acquisition time, T
based
assumptions:
C
Rs
Conversion Error
V
Temperature
V
17.2
If external voltage references are used instead of the
internal AV
ance of the V
considered. During acquisition, currents supplied by
these sources are insignificant. However, during
conversion, the A/D module sinks and sources current
through the reference sources.
In order to maintain the A/D accuracy, the voltage
reference source impedances should be kept low to
reduce voltage changes. These voltage changes occur
as reference currents flow through the reference
source impedance. The maximum recommended
impedance of the V
reference voltage sources is 250 .
DD
HOLD
HOLD
COFF
= 0 s.
A/D V
on
DD
REF
and AV
the
REF
+ and V
=
=
=
=
=
+ and V
following
SS
 2004 Microchip Technology Inc.
REF
REF
120 pF
2.5 k
1/2 LSb
5V
50 C (system max.)
0V @ time = 0
sources, the source imped-
- voltage sources must be
+ and V
ACQ
REF
R
SS
. This calculation is
application
- References
= 7 k
REF
- external
system